Files For 3D Printing

247 files

1. 

   Free

   SKV-DVC-B117 DAVROS-HEADREST TOP BAR.stl

   By jaguwa68

   The headrest top joining bar (item 3 in drawing headrest assembly drawing SKV-DVA-B004). Best printed horizontally to ensure clean visible surfaces.
   

   1 download

      (0 reviews)

   0 comments

   Submitted January 14

2. 

   Free

   SKV-DVC-B118 DAVROS-HEADREST STRUT.stl

   By jaguwa68

   The joining struts (item 4 in drawing headrest assembly drawing SKV-DVA-B004). 6 off required.
   

   2 downloads

      (0 reviews)

   0 comments

   Submitted January 14

3. 

   Free

   SKV-DVC-B119 DAVROS-HEADREST BUTTON COVER.stl

   By jaguwa68

   The button covers (item 5 in drawing headrest assembly drawing SKV-DVA-B004). 12 off required. 4 used to cover the screw heads.
   

   1 download

      (0 reviews)

   0 comments

   Submitted January 14

4. 

   Free

   SKV-DKC-SK138 Dalek-Receptacle, Quarter turn, Frt LH.stl

   By jaguwa68

   Design intended for quick release fixing of the fender to the skirt. To be used in conjunction with Pitking 44mm base 11mm grip quarter turn fasteners and spring retainers fitted to SKV-DKC-SK135 within the skirt lower panel. Please see SKV-DKA-F001 in link below for assembly details.  
    
    
   

   2 downloads

      (0 reviews)

   0 comments

   Submitted January 6

5. 

   Free

   SKV-DKC-SK139 Dalek-Receptacle, Quarter turn, Frt RH.stl

   By jaguwa68

   Design intended for quick release fixing of the fender to the skirt. To be used in conjunction with Pitking 44mm base 11mm grip quarter turn fasteners and spring retainers fitted to SKV-DKC-SK136 within the skirt lower panel. Please see SKV-DKA-F001 in link below for assembly details.  
    
   

   2 downloads

      (0 reviews)

   0 comments

   Submitted January 6

6. 

   Free

   SKV-DKC-SK140 Dalek-Receptacle, Quarter turn, RR.stl

   By jaguwa68

   Design intended for quick release fixing of the fender to the skirt. To be used in conjunction with Pitking 44mm base 11mm grip quarter turn fasteners and spring retainers fitted to SKV-DKC-SK137 within the skirt lower panel. Please see SKV-DKA-F001 in link below for assembly details. 2 off required. 
    
   

   2 downloads

      (0 reviews)

   0 comments

   Submitted January 6

7. 

   Free

   Vacuum chuck

   By Simchet

   Vacuum chuck for holding 100mm stainless steel spheres for drilling 25mm diameter holes to make weapon ball joints. Note - chuck is specific for bed on Bosch PBD40 pillar drill. There’s a boss in the bottom that locates in the 20mm diameter hole in the centre of the bed. This ensures the apex of the sphere is under the centre of the drill bit. The bolt holes also align with the T nut slots on the Bosh drill. That’s the only thing that makes it drill specific. 
   You need to add a strip of compliant material (rubber/draught excluder strip etc) to top inner surface of chuck to provide an air tight seal. Plug in a vacuum cleaner into the side port and it pulls the sphere into the chuck holding it securely. A strip of tape round the equator of the sphere helps increase friction to resist torque from the hole saw. Chuck must be fixed securely to base of pillar drill. 
   Chuck is specific for 25mm diameter hole saws as to drill the second hole you insert a short length of 25mm tube in the first hole that locates in a counter bore (25mm diameter) in the bottom of the Chuck. This ensures the two holes are aligned. You need to seal the bottom as the vacuum will be lost when the hole saw breaks through on the 2nd hole. Ring of hot melt glue between the stub of tube and the sphere works. Another ring of draught excluder seal in the bottom of the chuck would also work. If you do this keep the diameter of it as small as possible as you’re reducing the area that air pressure has to work on.
   If you don’t understand all of above and how vacuum chucks work, you shouldn’t be using the chuck. Take usual precautions when operating powered tools, I.e guards and PPE. Also note that stainless steel spheres are work hardened, use a hole saw with high speed steel teeth and run at a low speed and low feed rate. If work piece starts rotating, vibrating or spinning, stop immediately. 
    
   STL file and original CAD geometry files. CAD is in RS Design Spark Mechanical format (free). I suspect if you change the extension to .sdoc it will open in Ansys Spaceclaim as it’s basically the same software. Sorry, can’t export in parasolid/STEP with the free version of DesignSpark Mechanical. 
    
    
   

   4 downloads

      (1 review)

   0 comments

   Submitted December 23, 2023

8. 

   Free

   NSD Heronrib Neck Mesh Segment-Upper

   By jaguwa68

   Upper neck mesh segment (to be used in conjunction with SKV-DKC-N105 Mesh Lower and SKV-DKC-N106 Mesh Mid). Print time approx 10-12 hours. x8 required to complete each ring.
   

   16 downloads

      (0 reviews)

   1 comment

   Submitted December 21, 2023

9. 

   Free

   NSD Heronrib Neck Mesh Segment-Mid

   By jaguwa68

   Mid neck mesh segment (to be used in conjunction with SKV-DKC-N105 Mesh Lower and SKV-DKC-N107 Mesh upper). Print time approx 10-12 hours. x8 required to complete each ring.
   

   14 downloads

      (0 reviews)

   0 comments

   Submitted December 21, 2023

10. 

    Free

    NSD Heronrib Neck Mesh Segment-Lower

    By jaguwa68

    Lower neck mesh segment (to be used in conjunction with SKV-DKC-N106 Mesh Mid and SKV-DKC-N107 Mesh upper). Print time approx 10-12 hours. x8 required to complete each ring.
    

    21 downloads

       (0 reviews)

    0 comments

    Submitted December 21, 2023

11. 

    Free

    Movie_Dalek_Light_Lens.stl

    By AlanB01

    Movie_Dalek_Light_Lens.stl. Just been modeling the 60's movie dalek from the plans on here, great plans guys, so I thought I'd model the lights first so here is my take on the light lens, use as you will just give me a mention. Enjoy. 
    

    8 downloads

       (0 reviews)

    0 comments

    Submitted December 17, 2023

12. 

    Free

    Movie_Dalek_Light_Lens_Base.stl

    By AlanB01

    Movie_Dalek_Light_Lens_Base.stl. This is the base for the light lens it's been dished to fit the Dome
    

    4 downloads

       (0 reviews)

    0 comments

    Submitted December 17, 2023

13. 

    Free

    NSD Upper Neck Ring Segment (For 200mm bed)

    By jaguwa68

    Upper neck ring segment that incorporate the strut knuckle. x8 required to complete the ring. I glued each segment together one after the other using superglue and clamps, then filled on both the underside and the joints using U-pol Fantastic two part body filler.
    

    26 downloads

       (0 reviews)

    0 comments

    Submitted December 7, 2023

14. 

    Free

    NSD Mid Neck Ring Segment (For 200mm bed)

    By jaguwa68

    Mid neck ring segment that incorporates the strut knuckle. x8 required to complete the ring. I glued each segment together one after the other using superglue and clamps, then filled on both the underside and the joints using U-pol Fantastic two part body filler.
    

    20 downloads

       (0 reviews)

    0 comments

    Submitted December 7, 2023

15. 

    Free

    NSD Lower Neck Ring Segments (For 200mm bed)

    By jaguwa68

    Lower ring segments that incorporate the strut knuckle. x4 of N101 and x4 N102 required to complete the ring. The N102 includes a feature to fix in an M6 x 50 nut and bolt to locate the neck assembly to the shoulders at a later date. I glued each segment together one after the other using superglue and clamps, then filled on both the underside and the joints using U-pol Fantastic two part body filler. An alternative to wooden routed rings if, like me, your router (and routing skills!) are a bit dodgy.
    

    42 downloads

       (0 reviews)

    0 comments

    Submitted December 7, 2023

16. 

    Free

    NSD Hemisphere mounting

    By Prefect1938

    Hello,
     
    Hope you are all doing well. Please find attached my mounting for the hemispheres, like others I went for the 100mm bobbles which are nice but not very robust. To overcome this a bit and also help mount them I designed this mounting which incorporates a backing for the bobble so that it can be glued to it and therefor strengthening it considerably. It's so strong in fact that I can stand on it with my full Dad weight without it crushing, and yet it only weighs 41g! I have incorporated a hole though it so that a 5mm bolt or threaded rod can be simply screwed in to mount it to the skirt. It requires no supports, no brim and only 5% infill. I can print 4 at a time in 24hrs, increasing the printer speed to 120%. If you print it in black there is no further finishing required other than to fit your painted half bobble. I suggest printing one as a test to check it is a good match for your bobbles and if not a slight % change should be enough. A good test is to put a little blue-tack on the frame and to check that it is well squished when fitting the bobble. Please note the following Cura Standard setting over rides -
     
    Wall line count - 2
    Top layers - 4
    Bottom layers - 8
    Infill density - 5%
    Infill pattern - Triangles
    Support - None
    Build adhesion - None
     
    Any questions or comments very welcome.
     
    Thanks, Scott.
     
     
    

    11 downloads

       (1 review)

    0 comments

    Updated November 25, 2023

17. 

    Free

    NSD double walled shoulders in 16 easy parts for 300 x 300 x 400 printers

    By Prefect1938

    Hello,
     
    Please find the STL files for my 2005 Dalek’s shoulders. I took the original model shell from daviddz and put it into Tinkercad. There I added a further double skin with connecting internal blocks so that it would be rigid without any need to skin inside with GRP or further reinforcement etc. Once assembled the structure is very strong with no flex at all and is still quite light. This is great way to avoid building the complex curves in wood and will last a very long time. As the original sections were very large, I also split them up so that they would easily fit on my CR10’s 300 x 300 x 400mm bed. Some further simple cuts on some of the taller sections would get them to fit on smaller machines such as an Ender.
    All the 16 sections have been pre-orientated for printing and only two sections need any form of support, which saves a huge amount of material and build time. The two parts that do need support, only need a small amount of tree support on one side which just snaps off with no difficulty. Even if this is your first print you will find this a very easy project, although you will need to be patient as it’s a lot of printing. If you are confident in your printer, then some parts can be grouped on the same build plate, but it doesn't really save a huge amount of time to do so and risks losing two parts if something goes wrong. You will need about 8kgs of filament, and it is best buying this in 5kg spools which I hang of the wall. I just google for the cheapest stuff I can find.
     
    I have printed all the parts which have come out perfectly. To join the sections together I welded them with a 30 watt soldering iron rather than glue as it is much stronger. I have carefully split the sections so that joints would be easy to sand, I never bothered sanding the inside as it just looks like metal welding. For bed adhesion I have only been using thinned down white glue, about 5- 10% with water, this works great and have never had a failure. When working through so many parts I would recommend, just going from 1 – 16 printing one at a time. I have numbered the inside surface of the sections to avoid mix ups and added some matching assembly screenshots. I added two wooden rings to the inside of the top and bottom lips which were added before the front and back sections were welded together. I used Tiger seal adhesive between the plastic and wood which is extremely strong. Although the printing of these is really easy, it is a large undertaking so I would suggest you thoroughly study the files and confirm they will all fit on your machine, parts  14 & 12 being the tallest.
     
    Enjoy!
     
    I used the standard setting on Cura with the following overrides –
     
    All parts except 4 & 7
     
    Wall count = 4
    Infill = 20%
    Support type = none
    Adhesion type = Brim
    Brim with = 20mm
     
    Parts 4 & 7
     
    Wall count = 4
    Infill = 20%
    Support type = none
    Adhesion type = Brim
    Brim with = 20mm
    Support type = tree
    Support = touching build plate
    Support angle = 70degs
     
    I've tried to be as careful as possible but if I have goofed up somewhere let me know asap!
    

    351 downloads

       (1 review)

    0 comments

    Updated November 23, 2023

18. 

    Free

    NSD Eye rear with the correct 12 Ribs - Correction of previous part on site

    By Prefect1938

    Hi, this is a correct part of Mr McGoo's Dalek eye which after printing I realised that the number of ribs was wrong. So I have changed it to 12 ribs with no other changes made.
     
    

    31 downloads

       (0 reviews)

    0 comments

    Submitted September 6, 2023

19. 

    Free

    Movie Dalek.zip

    By iansarian

    Hi
    Here is my version of the Movie Dalek Dome, Neck, Eye, Gun and Claw Arm stls based on the forum plans.
    The files are designed to be printed on a small printer with a print bed 220x220.
    Regards
    Ian
    
    

    33 downloads

       (0 reviews)

    0 comments

    Updated September 4, 2023

20. 

    Free

    NSD dome rotation gears

    By Nimitz

    This gear and pinion is designed to fit a Lazy Susan which has a diameter for the inner ring of 415mm.  This Lazy Susan is the perfect size to be used on an NSD dome.  it may work for other domes but I've not tested it with anything but an NSD dome. You'll need to print 2 pieces of both the "A" & "B" parts.  the ends have lap joints for stability and the countersunk holes are for 10-32 size bolts.  the height of the gear has been designed so that you can leave the rubber feet that come with the lazy susan on the inner ring in place and the gear will be the same height. you will need to drill holes in the gear where your rubber feet are so it will sit flush with the bottom of your dome rotation plate.
    Note: the picture shows the gear sitting on the top of the dome rotation plate but that was just to take the picture.  the gear is mounted on the underside of the dome rotation plate which is why it is the same height as the rubber feet on the inner ring so it sits flush
    

    70 downloads

       (0 reviews)

    0 comments

    Updated August 29, 2023

21. 

    Free

    Scale NSD

    By Mark Casto

    Well, I have now printed out my first Dalek and I absolutely love it! Here are the gcode files for the Dalek and weapons sliced and ready to print if anyone else would like to print one out Im using the Ender 3 Neo and have just kept the standard setting. You will need to trim off the plastic around the weapons but it's no big deal the original Dalek is from Thingiverse if you want to give the creator a coffee awesome Dalek.
    

    32 downloads

       (0 reviews)

    0 comments

    Submitted July 18, 2023

22. 

    Free

    Planet Supreme Dalek: Eye Stalk

    By Necrosis

    This is a download for the Planet Supreme Dalek eye stalk. The files are in .stl format making them easy to 3D print or to use as digital references/models. These parts are 1:1 scale and match the most recent revision of the Planet Supreme Dalek plans making it plug and play to print or easy to scale to your Daleks needs. I personally 3D printed these units in colored SLA giving a refined finished look. Recommend printing these parts slow and precise at 15% infill for best results with standard 3D printers. Torch light files are based on "Sparky_Butane's" file and cross referenced with the Planet Supreme Dalek build plans as well as adapted for use with other included files.
    (Would love to see any print results from anyone who chooses to share on this thread)
     
    Details:
    Scale - 1:1 (In compliance with Planet Supreme Dalek Plans Version 3.2)
    Parts included in this download - Eye Stalk * Eye/Torch Piece * 3 Stalk Discs * Eye Pivot
    NOTE: For ease of assembly, parts have a 0.5mm to 1mm tolerance. The eye Pivot has a 12mm (1/2") hole in the center for a bolt and a larger hole on the backside that can be used to attach a control rod for the eye stalk.
     
    I will keep these files up to date and if you have any suggestions or find any errors please let me know so that I may update the parts.
    

    19 downloads

       (2 reviews)

    2 comments

    Updated July 5, 2023

23. 

    Free

    Drew' TDP 3D Model

    By SketchTwitch

    Hello everyone! I realized that there isn't a lot of files for the TDP build as it isn't as loved as the classic or 2005 Dalek models. Since I decided that I wanted to make the TDP as my first dalek build, I went ahead and modeled one of the plans from the forum. Attached is the zip file with all the parts individually, as well as a fully assembled model as STLs, at full size, though you can find the model on Onshape at: This link here incase you just want something specific.
    I haven't printed anything myself yet besides the plunger at 50% just to test my supports, I will be printing a split version of the neck rings and the shoulder model for my build! If anyone has any questions or request let me know!
    

    23 downloads

       (0 reviews)

    0 comments

    Submitted June 28, 2023

24. 

    Free

    NSD Oils Seals With Skirt Mounts

    By gazzer23

    These take a long time to print and can be fiddly with all the screws. However, once printed out they are so easy to put on and take off.
     
    Although I have made eight holes in the back plate, four screws are fine. They are extra in case of thread failure in the ring. You will need 4x3mm screws for each hemi plus 4xM2x6mm screws. They are for 100mm diameter hemispheres, either the clear plastic ones or the steel ones from China should be fine.
    

    20 downloads

       (0 reviews)

    0 comments

    Submitted June 27, 2023

25. 

    Free

    Customised 3D pieces for NSD from KiwiDoc's scrapmetaltron

    By kiwidoc

    (Oil Seal replica) Base for 100mm Acrylic hemis - press fit
     
    Neck blocks with a better placement of the ball and angled back slot
     
    Allan head bolt cap for fenders
    

    40 downloads

       (0 reviews)

    0 comments

    Submitted April 18, 2023