-
Registration
Please register an account to access the Forum topics and features.
An Active Membership subscription gives you access to extra features and exclusive content!
Choosing Active Membership is a great way of supporting the community and showing your appreciation for our resources.
Please note that you need to register BEFORE you can use Facebook, Twitter or Google as a sign in method.
Files For 3D Printing
Files that can be used to for 3D printing physical versions, using your own printer or a service such as Shapeways etc.
Note that files for CNC and laser cutting can be found in their own sub-section, inside.
245 files
-
Free
Full Size 3D Printable NSD-like Dalek
By elembivos
Hello all, I hope some of you find this useful, and no one finds it frustrating...
These are the STL files I designed and used to print Duma. You can read all the details here:
I used this project to gain experience both with CAD and 3D printing. Both of which I had no experience with before starting. I started at the top and worked my way down, and you can see how my skills developed a bit as progress was made. There are places where things don't quite match the plans, most notably the NSD dome grooves are missing. I didn't have the skills at the time I did the dome to make that happen. One other thing to note, that you might not notice is the eye stalk is slightly shorter than the plans. This was done intentionally to fit a lamp rod down the center to reinforce it. Straight up 3D printed stalk was not strong enough by itself. Likewise the gun and plunger have lamp rods through them too, but I used long enough rods that they could be trimmed to fit. I took artistic license here and there, for the most part it follows the plans.
If you are thinking of attempting this project you need to know a few things. First, again, I had little to no CAD or 3D printing experience before starting this project. There are probably better models in the downloads section for various parts, but I drew them up myself anyway in an effort to gain experience. So this is the WHOLE thing, designed to fit together. If you substitute someone else's dome, or eye, or whatever, don't expect it to fit without some additional work on your part. Even if you stick strictly to these STL files, not everything is perfect. Read through Duma's diary 5 or 6 times to see where I struggled, and needed to make modifications post print, to make it all work. I think the only file in the bundle that isn't what I used is the Cowl, and there all I did was remove the name from the ID indent, because you probably don't want your Dalek to be named Duma. That said, this project took over 2 years, spanning 2 computers. I did my best to assemble the STL files into one place before uploading them, but be prepared for me to have made a mistake and included one or two files that don't work, or there may be something missing. If someone comes across this, I should be reachable through the forum to figure it out. Second, for the neck and dome you'll need a variety of M3 nuts and bolts. There are many, and I don't recall all the sizes, so have a variety on hand. The skirt and base are held together with a variety of M5 nuts and bolts. Currently the neck is glued and screwed, everything else is just screwed. Eventually it will be glued, but for the moment it seems to hold together pretty well with just nuts and bolts. In the beginning I was printing the parts with threads in the part. Which works ok, but isn't super robust. Eventually I learned how to embed nuts in the parts, so the lower parts don't have that. Third, the dome was designed with animatronics in mind. So there are motor mounts for the eye, and rotation. The motors are described in the build diary, but if you can't get hold of the same part, you will likely need to make some significant modifications. I haven't included anything for motorization in the shoulder or base, so it is currently a static prop. Eventually I'll work out those details. If you get to it before me I'd be happy to bundle your efforts in here. Lastly, I had no CAD or 3D printing experience when I started, so don't judge me 😉.
P.S. Someday I plan to update the files to include "what I would do if I had it to do over again." But don't hold your breath.
563 downloads
-
Free
Renegade_Dalek_Kit.zip
By audrey2
I ended up modifying quite a lot of the pieces so they now all fit together and print really well. It's a great balance between detail and ease of construction. So I have no doubt that any member of Project Dalek would be able to assemble it. It's a great deal simpler than the NSD, which was more designed for me with other people being able to assemble it simply being an afterthought.
As such I've created an instruction manual for anyone interested in either putting the model together or simply seeing how it was designed.
Renegade Dalek Instruction Booklet.pdf
235 downloads
-
Free
Imperial Dalek 5 inch Model Kit
By audrey2
To make up for the fact that there is no sufficiently accurate 5 inch model Imperial Dalek, here is a small 3D printable model kit to create your own.
This was modelled in Blender, with FDM style 3D printing in mind (although if anyone makes a resin one, please let me know, I'd love to see how it turns out), and the parts have a tolerance of around 0.15mm to fit together.
Only the plunger and the shoulders require printing with support material, and I have provided a visual instruction booklet showing the basics of how to assemble the model.
263 downloads
-
Free
Evil of the Daleks - Emperor Dalek 5 Inch Model Kit
By audrey2
This is a model kit of the Emperor of the Daleks from Evil of the Daleks.
It should print in scale with the Character Options dalek figures. It should print with no supports required if you have a well-tuned printer printing at a high enough resolution.
Print 12 of the hemi_large, and 2 of the hemi_small, and you'll have everything needed for a Dalek civil war.
173 downloads
-
Free
Mk 1-2-3 EyeBall
By Luke S
Come With multiple Different iris/lids! You Can Mix and Match!
You Can Modify them If You Like.
Includes:
Mk1 Eyelid
Coming Soon!
POWTD eye front and Iris MK3 Shorten Toffee lid MK2 Barnardo Eyeballs Mk3 Evil of Daleks Pupil Iris. Mk2 EyeLids(Different Hole Diameters) Mk1-2-3 Eye Back Mk1-2 Eye Front Mk2 Toffee Apple Front & EyeLid
581 downloads
-
Free
NSD Eyeball
By Slythenperior
This is my version of the 3d printable 2005 Dalek eyeball. The thing that makes this different is the screw function allowing the front of the eye and the back to screw together. This is in case something goes wrong with the wiring and the light stops working. Just thought it would make things easier for everyone. Enjoy
457 downloads
-
Free
Dalek Thompson Submachine Gun
By Peekaymac
I drew these up so that my spotter could easily be in costume as a recognizable character that wasn't restrictive or limited movement. Basically they just need to wear 1930's style clothing and carry the Thompson and it's done. Oddly I didn't 3D print my own version - it was made by hand but I subsequently made these files for others to use.
You'll need:
6x Barrel Tines
2x Magazine Side 1
I have each of the magazine faces mirrored on my model but I can't remember why now.
1x each of everything else
I allowed 1.75mm pin holes for joining all the parts together.
Any questions please ask.
983 downloads
-
Free
Complete NSD Scale Model
By audrey2
All the parts for a scale NSD that can be printed and assembled.
The parts are designed to go together at a 1/5 scale, and while it may work in other scales I haven't tried them yet, so that's up to you to play around with.
You can see how I printed mine and put mine together when printed on a Replicator 2 here.
285 downloads
-
Free
2005 Plunger
By elmoray
I wanted to give back to the group...
Here is a version of the 2005 plunger that I made for my Dalek. You can find more info on Thingiverse: http://www.thingiverse.com/thing:210939
315 downloads
-
Free
NSD: Light Cage
By Ultrastar
NSD: Light Cage
By: Ultrastar
Intended for Dalek builders out there with the ability to 3D print models. This is a 3D model of the NSD Light Cage. This model was created with the purpose of 3D-Printing. However, with this being a 1:1 scale and 100% accurate model it can also be used as a reference for your own builds. Feel free to ask questions about this model as you see fit.
774 downloads
-
Free
Full Scale Shawcraft Dalek Dome Model and Negative
By Omeganinjaboy
The dome is based on the Version 3.1 Movie plans (so the eye slot is higher than other classic domes), though the negative and back half files are consistent with other classic domes dimentionally. You could just print two back halves if you do not want a movie dome and cut the eye slot yourself. I would advise you consult the dome dimentions in the Version 3.1 Movie plans and compare them against the dimentions of your own plans if you are building a different classic dome.
This is a 3D printable Dalek dome model that has a curved eye slot rather than a rectangle extruded one making it more accurate to the real thing (It took quite a while to figure out how to make a hole based on a curved measurement in CGI). The front and back halves are provided, but you will have to slice it up if the model is bigger than your printer's build volume. The skinny dome is half an inch (1.27cm) thick and the normal one is one inch (2.54cm) thick. There are lower poly and higher poly (HD) variants of most files. A negative of the dome is also included for you want to use however you wish.
336 downloads
-
Free
Exploded NSD dome for 3D printing
By cjorgensenmd
This in my NSD dome sliced into manageable files for 3D printing. Each section is still fairly large. you will need at least 200mm x 200mm print area, but once everything is printed, they can be attached to a lasercut base and then glued together for a very accurate NSD dome which will require very little finishing before a fiberglass mold is made. I have included both the raw solidworks files as well as the STLs in case anyone would like to make edits. I will edit this post once I have all 16 sections printed. I have two so far and they each took about 14 hours to finish, so this is a patient process.
367 downloads
-
Free
NSD eye pivot holder
By cjorgensenmd
Designed to hold my 3d printed NSD eye pivot and support the interior dome. The base is as thick as it is because I needed the extra height to get the eyestalk where it needed to be from my rotating base. The little horizontal rod on the lower side of this piece is itended to be used to attach a spring to counterbalance the weight of the whole eye.
542 downloads
-
Free
Servo Iris Assembly
By trickster
UPDATE: I noticed lots of people are downloading the model files one at a time. It's much easier to download the complete package and avoid the download limits. Here's the zip: ServoIris.zip
UPDATE: There are pictures illustrating the assembly process in my build diary. Note that there are two iris versions in the diary. This is the second one.
This is a complete set of 3d objects to create a micro servo driven iris insert. It is designed to fit into this eye with a little bit of sanding and work with this servo and this LED disk. All parts have the proper clearances based on my printer using .2mm layers. Some of these are pretty close to the wire and you might have to fiddle a bit. I printed everything but the LensPlate using white ABS and painted various surfaces black. The LensPlate is translucent blue ABS with an acetone vapor bath. The leafs and SlotRing were lightly sanded smooth.
Objects included (bottom up):
Casing SlotRing peg (6 required) leaf (6 required, note the stl file is flagged as broken and can't be repaired, but it prints ok. Don't use a raft.) LensPlate (print using translucent filament) [LED disk] LockRing (orients with tabs at the top) DualSlotLEDPlate (LED disk attaches to this) ServoArm (servo horn fits inside) [servo horn] ServoArmCover ServoMountRing ServoStandoff (2 required) ServoMount [servo] ServoMountCap
Check out my build diary for pictures illustrating assembly described below. Note that there are two iris versions in the diary. This is the second one.
Assemble the Bottom Iris Section
Assemble the slot ring into the casing. Spray the front and inner lip flat black.
You will need to print 6 each of the leafs and pegs. Then assemble each peg and leaf so that the peg sticks out the opposite side from the post on the leaf. Give them a light sanding to get them smooth. Now paint them flat black and sand smooth again. Leaf assemblies orient with the offset post (the one printed as part of the leaf) down. You have to get all 6 properly nested.
The LensPlate is printed with blue translucent filament and acetone vapor bath smoothed out. Orienting this piece is the tricky part. You will probably have to spin it a few times to figure out which way works. LockRing goes on top of the LensPlate and fits the slots of the casing. You have to clear out the tiny support thingies on the casing btw. Orient the LockRing with the tabs on top.
The LED disk has 4 holes punched in it. Find the pair that fits the DualSlotLEDPlate and press it on with the wires through the hole. Then add the plate to the stack with the LED facing down. The posts on the LensPlate should be at one end of the slots and should move within the slots to open and close the iris. If this is not the case, try disassembling and rotating the LensPlate one step around the leafs until you find the way that works.
At this point you should be able to operate the iris by hand. This is a good time to sand the outside of the casing and inside of the eye front until they fit together properly.
Assemble the Top Servo Section
I used the micro servo with feedback from Adafruit. Eventually I plan to use the feedback wire to know the servo's current position. I believe the non-feedback micro server is slightly different and probably won't fit this mount. You could use a different servo but would have to adapt the ServoMount and ServoMountCap. Trap the servo between the ServoMount and ServoMountCap so that the servo shaft is in the center of the mount. The pieces should fit together snugly.
The servo comes with several horns. Find the one that matches the hollow in the ServoArm. Trap the horn between the ServoArm and ServoArmCap and snap the pieces together. It only fits one way.
Rotate the servo shaft by hand to determine the limits and set it to the center of its range. Attach the arm assembly to the shaft so it is at a right angle to the servo mount and secure it with the screw.
Assemble the servo assembly, two ServoStandoffs, and the ServoMount Ring. If the standoff pegs are too tight, lightly ream out the holes.
Final Assembly
Operate the iris by hand so it is at the halfway point. Attach the servo assembly to the iris. Everything should be properly oriented and the servo assembly should fit snugly on the casing. Make sure all the tabs are lined up. Try operating the servo arm by hand and verify the iris opens and closes. It will not close 100% and will probably not reach the limit on the slots.
Now you have to connect it all up. I used an RJ45 socket and ethernet cable connected to a Raspberry Pi with Adafruit servo/PWM and PifaceRelayPlus HATs. Here's the software. You will have to experiment with the servo to determine what relay and PWM values to use.
Here's the zipped objects: ServoIris.zip
484 downloads
-
Free
"Eve of the Daleks" Gatling Gun for NSD. Full Size, Rotating
By threegringos
This is the NSD "Gatling Gun" weapon as seen on the trailers for the 2022 New Year's episode "Eve of the Daleks".
This 3D model was made before the episode aired, so the scren shots were very limited. It looks accurate to my eye, however more details may become apparent once we get to see the entire episode.
I used Fusion360 to create this model. It's split into multiple parts for ease of printing.
You will need to provide a 25.4mm (1 inch) diameter pipe for the arm, and also mount a suitable 102mm (4 inch) ball-joint. I always use magic 8-ball toys for my ball joint.
The eight small pipes coming out of the rear of the gun part are 6mm diameter. You can either print them from my files, or optionally use stainless steel drinking straws, cut to length.
I did include an internal gear in the main body of the gun, and an additional pinion gear in case somebody wants to motorize the rotation of the weapon. I haven't had time to figure that out yet.
126 downloads
-
Free
Death to Daleks Projectile Gun
By erichdalek
Designed off of user Ramjet's plans-- Complete version without allowance, each other part with allowance for main gun part fit.
492 downloads
-
Free
Cdngoose 2008 Davros
By cdngoose
Included in this package of STL files are all the parts I have printed off for my 2008 Davro's panel. Also included are the measured blueprints for each piece. This way you can ensure the parts are exact or re-size them to fit your panels. Please look to Cdngoose 2008 Davro's build for information on how they were created and used. All of these files were created for me by Phillip McNulty, I owe him a Huge Thank You for not only making me these STL files from his CAD drawings but for allowing me to share them with all PDF members.
All files were printed in PLA filament as well as the rubber boots were also printed in flexible PLA
Hope these help others in their building process. Though they do not make exact reproductions of the TV show parts I believe they are more than close enough that when fans take pictures while standing beside Davro's they will be very pleased!
Cdngoose
1,285 downloads
(2 reviews)0 comments
Updated
-
Free
NSD 3D Print Components
By tlmxcpmpp
File contains various New Series Dalek components for 3D printing, including...
Claw Cowl Dome Dome Turntable Eye Gun components. Hemisphere Neck Rings Slats
Photo shows Dalek built using these components (along with traditional build methods).
439 downloads
-
Free
NSD Moflash Cage For 3D Printing
By Ferrain
Second published attempt at anything like this, for 3D printing so please be gentle.
NOTE The screenshots show some pieces that have been printed unsanded & untrimmed & they also show cages V1.99 & V2 (The only part that is constant in both is the top ring), from the test fitting a roll back to V1.99 for the supports & base may be required for a deeper recess of 3mm.
The Top ring takes about 30 - 40 minutes on a Replicator 2 at Highest Quality settings.
A support piece takes about 32 minutes on a Replicator 2 at Highest Quality settings, these could be multiplied up to the required 8 for the output file.
The base will take about 3 hours on a Replicator 2 at Highest Quality settings.
It is suggested that a hot pin be pressed through the build material using pliers & suitable heat source for each support at the top & bottom rings after gluing for additional strength.
Despite various efforts a one piece print has not gone smoothly so still a kit of 6 parts not including Moflash lens, if a one piece is successfully produced, the file will be added as a compliment.
Constructive feedback welcome.
518 downloads
-
Free
MK1/2/3 & Movie 1/2 Stalk/Pivot Set!
By Luke S
So you have a budget , or don't know how to taper wood.
A 18mm hole has been added so that you can use them, if you just used the eyestalk without a 18mm rod it would break from the weight.
So I used the Mk1 Dalek Blueprints to Make these models.
IF You have Downloaded any of my Prints please Pm if I have added or edited it, so i can send you the newest copy.
Print Settings
Printer brand:
Creality
Printer:
Ender 3
Infill:
100%
Filament_brand:
Filament_color:
white, Black, Gray
Filament_material:
PLA
194 downloads
(0 reviews)0 comments
Updated
-
Free
Full Scale Shawcraft Dalek Dome
By Chris Moliere
My class just gave us Fusion 360 accounts, so I whipped this up in my spare time. This is based on the most recent Shawcraft Dalek plans, as of upload. Since my printer doesn't have the proper build volume to accommodate the entire dome, it has been split into sixths. Enjoy!
359 downloads
-
Free
Movie Beaker (Updated)
By WhosWho
Here's my model of a Movie Dalek Beaker. I hope this helps any who don't have an original to take molds from.
196 downloads
-
Free
-
Free
Imperial Dalek Dome lights - STL
By Aaron J Climas
After the plans change on the domes/ dishes I went away and redesigned my 3D model. And although the pictures here are of the old dishes, I have
since printed out the new sized ones. They seemed to work well, the pipe I believe was around 12 months, and the dome about 25. Much faster times
due to the much smaller objects.
OLD INFORMATION ON PREVIOUS VERSION.
I needed a set of Imperial dome lights. The EMA parts looked expensive, so I 3D modelled and printed out a set myself.
When I imported them the models came in factor of 10 too small. However in STL viewer and Maya they seemed the correct size. So may have been an issue
with the printer software.
The pipe took me 18 minutes to print, and the dome 43 minutes. So just on two hours for the full set.
I thought I would share. If you have issues, give me a shout and I will repair the files.
90 downloads
(0 reviews)0 comments
Updated
-
Free
Gun Boss rear
By chrisosborne
Changed relief at back for ball joint, otherwise solid. Holes on the model are oversized.
247 downloads
-
Top Downloads
Week
-
Free
-
.thumb.png.da17fe0bc84834e71bb4ac8d57a579f8.png)
Free
-
Free
-
Free
-
Free
Month
-
Free
-
Free
-
Free
-
Free
-
Free
Year
-
Free
-
Free
-
Free
-
Free
-
Free
All Time
-
Free
-
Free
-
Free
-
Free
-
Free
-
-
Recent File Reviews
-
Mark Sheriff 6
Excellent , looks great and very well designed , well thought out . thank you
-
Marc Harris 41
I'm in my 50s and have since I was a boy watching Dr Who in the 70s always dreamed of making a Dalek for fun, now I have the time and resources, along with your forum's help it's time to live that dream.
I have watched some of the members videos, and I am very impressed with what I have seen.
Long live the Who verse.
I will document my progress and share any innovations I make
-
Chris R 25
Great set of models that printed and fitted together really easily. Can't comment on accuracy as I'm no expert but very happy with the result
-
Dalek Hal 312
Great file, easy to print
-
doctorone 3
Great plan but the pivot does not print as it is not complete like the eye stalk
-
71Davros 2
These plans seem to be very concise and detailed. Hopefully, there shouldn't be any problems making the Dalek now.........
-
-
Download Statistics
-
Recent File Comments
-
By John · Posted
See this FAQ topic for more on Downloads availability: -
By ChristmasDalek · Posted
Welcome to the forum! Sorry you have encountered a problem... While waiting for someone who knows more about the downloads section than I do to answer, you may find the explanation in @Johns answer to this thread: Be well, Kathy -
By tardis112 · Posted
Why am I not permitted to download this? -
By Mark Casto · Posted
This is such a useful file for the eye it is perfect for adding a fish tank led inside and looks great thank you. -
By DarthCranium · Posted
ok @Bodule. i apologize if i caused any issue. -
By Bodule · Posted
Hi @DarthCranium Can I suggest that you ask your question in the 3D Printer Discussions section of the forum please? https://www.projectdalek.com/index.php?/forum/209-3d-printer-discussions/ That section itself may be worth a read through, as is @ChristmasDalek's post above yours 👆 here as it may provide additional useful information on how to use the forum. -
By DarthCranium · Posted
What is a good size of 3D printer youd recommend if i wanted to make a dalek of my own? please let me know when able. Thanks -
By Dalek-Nik · Posted
Moflash lenses appear to be slightly difficult these days. the best bet in my opinion is 3D printing them. there are many accurate models here that can be printed on any FDM printer you can find. there is a chance that you can find the lenses online to buy, but those sites can be slightly sketchy. depending on the filament you buy and the printer you have/find, they can be produced fairly accurately. filament can come as cheap as 17 dollars, but do keep in mind that they can some -
By Chris R · Posted
Thanks for uploading these files. Printed really nicely with the odds and sods of filament I had around and very pleased with it, haven't done any tidying up or painting but it looks great as-is.
-
-
Highest Rated Submitters
No ratings this week.
No ratings this month.
-
1
-
2
-
3
-
4
-
5
-
1
-
2
-
3
-
4
-
5
-
-
Current Donation Goals
-
Finance the Forum Hosting 2024Raised 100.00 GBP
-
-
Top Templates
-
Free
-
Free
-
Free
-
Free
-
Free
-
