-
Registration
Please register an account to access the Forum topics and features.
An Active Membership subscription gives you access to extra features and exclusive content!
Choosing Active Membership is a great way of supporting the community and showing your appreciation for our resources.
Please note that you need to register BEFORE you can use Facebook, Twitter or Google as a sign in method.
Files For 3D Printing
Files that can be used to for 3D printing physical versions, using your own printer or a service such as Shapeways etc.
Note that files for CNC and laser cutting can be found in their own sub-section, inside.
248 files
-
Free
Slat-small-shell-STL
By acrylikhan
STL File for stereolithography. NSD Shoulder Slat: Size Small. File Version 2.0
192 downloads
-
Free
NSD Eye STL Files
By henryjolly
Eye2 is hollow without a stem and Eye4 is hollow with a stem. Perfect for printing then adding an LED.
350 downloads
-
Free
-
Free
300mm_ISD_Gun_Collar.skp
By Ferrain
This sketchup file produces a 3D model of a robust (chunky) classic gun rod collar when exported to STL & the 3D printer of your choice.
The reason I have uploaded it as a Sketchup file (in a zip format), is that if you select the whole model, then press , the model is surrounded by a cube which allows you to increase or decrease the overall model size, allowing you to tailor the inside diameter of the collar, to the outside diameter of the gun barrel.
It allows for about 5mm depth of support for a gun rod (once drilled out to suit your rods) to be affixed with epoxy resin of similar.
Earlier versions of the file produced one defective gun rod support - This model has extruded all pushed all the outer faces of the supports back into the main collar in a attempt to correct that defect. Should that not be the case, then I will create a new model when I get chance.
In HQ 0.1mm layer height & 5% infill it takes about 1.2 hours to print on a Makerbot Replicator 2.
39 downloads
-
Free
NSD 2005 Oil Seal
By glynharper
This is my own design for an oil seal replacement.
It's not perfect, as the edges are a little faceted. Although I actually don't mind that myself as it appears more 'machine made' which I think suits a Dalek's appearance.
It incorporates an inner lip, in order to centrally locate your hemisphere. There is also a central part, which has a hole and a hexagon recess for a standard M6 head head bolt. This is to eliminate the requirement for MDF discs or other mounting methods to be stuck inside the hemis.
The idea is, but an M6 bolt through the hole (which is a tight fit to stop it dropping out.. tap it in if need be).
Then put a bead of black silicone in the recess of the oil seal and push the hemi into it. You can silicone inside as well, as there is access to do so.
The central supports are a ribbed structure, to stop the oil seal being able to be pulled away from the skirt easily.
Although the central recess will lock the M6 bolt in place, bear in mind it's still plastic so it will easily break if you put too much torque on the nuts you use to hold the oil seal on with. Best not to use lock nuts, but use normal nuts with spring washers, and some loctite. Nip them up, but don't over tighten them.
Would love some feedback, as this is my first design for a 3D printed Dalek part.
65 downloads
-
Free
Imperial Dalek Eyeball
By Aaron J Climas
Hey guys.
This is a STL file of the Imperial Dalek eyeball. It's in two halves that need to be printed and glued together.
It is a pair of STL files. They are much larger than normal as I have found issues with low resolution geometry making the prints come out with hard edges. If this is too much geometry I will remodel and upload again.
The front of the eye isn't as deep as the original prop, because it makes adding the front much harder! However I could do that variation if someone was keen.
The front of the eyeball itself is slightly rounded off as per the original, rather than being dead flat.
The rear of the ball has a nice flat section for tube to sit flush against, as well as a pilot hole included for drilling a central hole.
I haven't printed this file yet, but intend to tomorrow!
EDIT. The rear of the eyeball has a hole in he model. I have fixed the model, but not uploaded yet. This will be fixed soon.
EDIT- The previous upload didn't include the front of the eye. I only just saw a message about it then. (4th March 2016.)
95 downloads
-
Free
Printable Oil Seal Surrounds and Hemispheres (Glowing?)
By Kresty
My take on oil seal surrounds and hemispheres... I'm not sure these are practical as it takes an hour to print a surround and a couple for a hemisphere, but here they are...
The reason I did this was because brialath has talked about a Disco Dalek and I wanted to see if WS2812B LEDs would be able to light a 100mm hemisphere. Since I made the hemisphere, I decided a mount for the aforementioned LEDs built into the surround might be good, and the traditional center bolt doesn't really work because the LED needs to be there.
Since I could I also made a solid hemisphere that might print better, and a surround with a centered bolt hole for an M4 bolt, and a little block to keep the bolt head from turning. I considered glynharper's surrounds, however I wanted an exact fit for the hemisphere I'd made, and I wanted a enough room for a 12-14mm washer to distribute the load. So that meant I needed a block to hold the M4 bolt head, the recessed version wouldn't work. Also, of course I needed a version with a spot for the LED in the middle.
The surrounds are intended to fit exactly in the middle of the hemisphere. They probably need some sort of adhesive, but for my printer it was a really close fit.
Since normal humans could reuse these for xmas ornaments or something, I put them on Thingiverse, with more info... http://www.thingiverse.com/thing:726897 (including the openscad & sketchup files for them).
138 downloads
-
Free
NS Center Slat
By acrylikhan
Center Slat for New Series Dalek Design, Full Scale, Dimensions should be in Metric. Part should print on any 3D Printing Machine, test prints were achieved successfully with:
Objet/Stratasys Machines: Eden 333, Eden 500, and Connex 2 and Fortus 450mc (FDM)
3D Systems: SLA500, Projet 1200 (SLS)
181 downloads
-
Free
Imperial Dalek: Gun Box Surrounds
By Necrosis
This is a download for the Imperial Dalek Gun Box Surrounds. The files are in .stl format making them easy to 3D print or to use as digital references/models. This part is 1:1 scale and match the most recent revision of the Imperial Dalek plans making it plug and play to print or easy to scale to your Daleks needs. I personally 3D printed these units to create a mold that allows me to cast the part with perfect detail, SLA printers work great to get to that finished look quicker. As noted in the plans; the original props where easily damaged during filming do to the ball joint openings being thin, I would suggest slightly flexible resin for casting or 25% infill for plastic printing to give greater resistance to stress. The parts look great as 3D prints alone with some filler and primer and detail work. The surround piece has a 101mm recess in it to allow a 100mm ball joint to stick out as they do in the show. Included in the download is another file that is the same but without the recess for those that don't want it. Recommend printing these parts slow and precise at 15% or 25% infill for best results.
(Would love to see any print results from anyone who chooses to share on this thread)
Details:
Scale - 1:1 (In compliance with Imperial Dalek Plans Version 3.5)
Parts included in this download - Gun Box Surround w/recess - Gun Box Surround w/no recess
I will keep these files up to date and if you have any suggestions or find any errors please let me know so that I may update the parts.
33 downloads
-
Free
NSD Eyestalk Keyed Base
By cdngoose
This file is for the NSD eyestalk base, it was created by Ray Arell in Oregon USA. I have not printed this file yet but I like the ability of the keyed insertion of the eyestalk into the Base.
Cdngoose
from Ray
This is the base of the Dalek eye stalk. I wanted an easy method to access the dome electronics, so I put the eye stalk on a keyed lock. You insert the eye stalk and rotate it to lock it into the base.
Dalek Eye Stalk Base by elmoray is licensed under the Creative Commons - Attribution - Non-Commercial license.
So what's this mean?
Remixing or Changing this Thing is allowed.
Commercial use is not allowed.
93 downloads
-
Free
NSD centered oil seal
By beeweasd
i found one similar to this but it was slightly to big, so i made one with the correct dimensions.
171 downloads
-
Free
Death to Daleks Projectile Gun
By erichdalek
Designed off of user Ramjet's plans-- Complete version without allowance, each other part with allowance for main gun part fit.
501 downloads
-
Free
NSD: Front Gun Box Detail
By Ultrastar
NSD: Front Gun Box Detail
By: Ultrastar
Intended for Dalek builders out there with the ability to 3D print models. This is a 3D model of the NSD front gun box detail. This model was created with the purpose of 3D-Printing. However, with this being a 1:1 scale and 100% accurate model it can also be used as a reference for your own builds. Feel free to ask questions about this model as you see fit.
197 downloads
-
Free
NSD eye pivot holder
By cjorgensenmd
Designed to hold my 3d printed NSD eye pivot and support the interior dome. The base is as thick as it is because I needed the extra height to get the eyestalk where it needed to be from my rotating base. The little horizontal rod on the lower side of this piece is itended to be used to attach a spring to counterbalance the weight of the whole eye.
549 downloads
-
Free
Magic 8 Ball Inner Sleeve
By redman99
This will slide into a magic 8 ball and sit against the inner ring, and the outer hole.
Should keep it nice and sturdy, and allow your alu tube to slide right though.
73 downloads
-
Free
Renegade_Dalek_Kit.zip
By audrey2
I ended up modifying quite a lot of the pieces so they now all fit together and print really well. It's a great balance between detail and ease of construction. So I have no doubt that any member of Project Dalek would be able to assemble it. It's a great deal simpler than the NSD, which was more designed for me with other people being able to assemble it simply being an afterthought.
As such I've created an instruction manual for anyone interested in either putting the model together or simply seeing how it was designed.
Renegade Dalek Instruction Booklet.pdf
238 downloads
-
Free
Classic Dalek gun cage base rings
By BlueHinter
Two 29mm rings designed to form the front and back of a classic series Dalek gun cage. Interior dimensions designed to snugly fit 1" conduit, with a slight gap in the center for adding glue.
The 8 holes around the perimeter should be about the right size for the cage pieces if using old coat hangers, but can easily be drilled out to any size required.
75 downloads
-
Free
NDP Neck Rings
By threegringos
I created these files for Orin - my NDP Dalek build. All measurements were taken from the PDF plans.
You need to print 12 of each file. I used PLA with 1mm wall thickness and 10% fill, but I would advise to go thicker - maybe 1.5mm, as the parts will warp under direct sunlight. Alternatively, try using ABS, which is less sensitive to ambient temperature.
For assembly, start at the bottom with Layer 1, then build up as follows: Layer 2 base, Layer 2, Layer 3 base, Layer 3, Layer 4 base, Layer 4. I added some strength by offsetting each base layer so that the joints did not all align vertically.
291 downloads
-
Free
Imperial Emperor/Davros Parts
By Chris Moliere
These are the parts for the Imperial Emperor from Remembrance of the Daleks, all in full scale. Please note that I didn't include the skirt, as that is a lot easier to construct from wood or fiberglass. I also didn't slice this set, so people could cut the file to their preferences. I would recommend printing the eye in flexible filament, since I use the straight measurements for its model; the outside is higher than the inside to help make painting it easier. Also, the dome thicknesses vary from 6-8 mm, so if you want it any different thicknesses, feel free to contact me. Please enjoy!
66 downloads
-
Free
Moflash Lens
By WhosWho
A hi res STL based on the Moflash lenses used New Paradigm and New Series Daleks.
135 downloads
-
Free
Classic Dalek Appendage Seismic Detector
By Luke S
A Zip File of the whole items is in the download to save up download room.
There are 7 parts, the Bottom Half, numbers, the top, white band, outer gyro ring, inner gyro ring, and Diel. There are already to holes in the print for the dial thingy that spins and the rods that connect to the gyro. The holes for the rods in the print are 4 mm in diameter. US Also You may need to add washers around the pins to stop the rings from sliding off. Thanks to @James O and @Dave'O for there estimated gused blueprints.
IF You have Downloaded any of my Prints please Pm if I have added or edited it, so i can send you the newest copy.
Unauthorized sales and distribution, in any format, is strictly prohibited.
Print Settings
Printer brand:
Creality
Printer:
Ender 3
Infill:
100%
Filament_brand:
Filament_color:
white, Black
Filament_material:
PLA
107 downloads
-
Free
Dalek Destiny Bomb
By Luke S
I just finished making my other 3d print of the Dalek Destiny Bomb. I notice people were looking what the bombs were, but could not find what it was, So i decide to make this. The Yellow band Is Not in the File! You should use yellow paper like the prop did!
If you find that its measurements should be changed then tell me and I will update them.
IF You have Downloaded any of my Prints please Pm if I have added or edited it, so i can send you the newest copy.
Unauthorized sales and distribution, in any format, is strictly prohibited.
Print Settings
Printer brand:
Creality
Supports:
Yes
Resolution:
0.1mm
Printer:
Ender 3
Infill:
100%
Filament_brand:
Filament_color:
red
Filament_material:
PLA
39 downloads
-
Free
Evil of the Daleks - Emperor Dalek 5 Inch Model Kit
By audrey2
This is a model kit of the Emperor of the Daleks from Evil of the Daleks.
It should print in scale with the Character Options dalek figures. It should print with no supports required if you have a well-tuned printer printing at a high enough resolution.
Print 12 of the hemi_large, and 2 of the hemi_small, and you'll have everything needed for a Dalek civil war.
175 downloads
-
Free
NSD Cowl Quadrants
By Pgordon
This is the NSD Cowl 1.0.0 By Macropod80, but split into 4 roughly equal sized quadrants which can be printed on printers with a much smaller build area. I created these splits for my Flashforge Adventurer 3 which only has 150x150x150 build area, and they print fine, and join together pretty well with nice tight seams. Someone more proficient at 3D modelling than I could perhaps improve these models by adding some alignment/reinforcing tabs along the joins to aid with accurate assembly and strengthen the joins in the assembled piece. In my case I joined the pieces with superglue and held them together by hand while the initial bond formed.
Whilst the seams are fairly tight & neat, they're not invisible, so the completed assembled cowl will still need filling, sanding & painting. The parts need to be printed with supports, which are not in these model files, you'll have to add them in your slicer.
I printed these in PLA with 0.2 layer height, and each quadrant is roughly a 16 hour print at the highest quality on my machine.
Hope this helps someone!
238 downloads
-
Free
Imperial Dalek : Dome Lights
By Necrosis
This is a download for the Imperial Dalek dome lights. The files are in .stl format making them easy to 3D print or to use as digital references/models. These parts are 1:1 scale and match the most recent revision of the Imperial Dalek plans making it plug and play to print or easy to scale to your Daleks needs. I personally 3D printed these units to create molds so that I can cast the parts. I cut the center piece from acrylic using the print as a template. However, the parts look great as 3D prints with some filler and primer and you can print the center disc from a transparent filament with out any hassle; SLA resin printers also work great for this kind of part. Recommend printing these parts slow and precise at 15% infill for best results.
(Would love to see any print results from anyone who chooses to share on this thread)
Details:
Scale - 1:1 (In compliance with Imperial Dalek Plans Version 3.5)
Parts included in this download - VHE-275 * Acrylic Disc * VT-250
NOTE: For ease of assembly, parts VT-250 and Acrylic Disc have 6.5mm holes through them, this allows a 1/4" bolt or 6.35mm bolt to go through and connect them; there are two recessed locations on part VHE-275 (Elliptical head) where the hex/head of the bolt can be mounted in place. This is not visible from the outside and ensure perfect placement of the parts and allows easier installation on the dome. All parts also have a 26mm hole in the center to allow the placement of a small bulb.
I will keep these files up to date and if you have any suggestions or find any errors please let me know so that I may update the parts.
21 downloads
-
Top Downloads
Week
-
Free
-
Free
-
Free
-
Free
-
Free
Month
-
Free
-
Free
-
Free
-
Free
-
Free
Year
-
Free
-
Free
-
Free
-
Free
-
Free
All Time
-
Free
-
Free
-
Free
-
Free
-
Free
-
-
Recent File Reviews
-
Michael56 4
I'm in my late 60's. I live in Australia and have always enjoyed Doctor Who from the very first episode aired here around 1965 when I was 9 years old. Thought how amazing it would be to have a Dalek but had no idea how or where to even begin UNTIL I came across this site. Thanks for giving me the opportunity to at least be able to start on a Dalek build and will detail my progress as it goes along.
-
Mark Sheriff 6
Excellent , looks great and very well designed , well thought out . thank you
-
Marc Harris 64
I'm in my 50s and have since I was a boy watching Dr Who in the 70s always dreamed of making a Dalek for fun, now I have the time and resources, along with your forum's help it's time to live that dream.
I have watched some of the members videos, and I am very impressed with what I have seen.
Long live the Who verse.
I will document my progress and share any innovations I make
-
Chris R 25
Great set of models that printed and fitted together really easily. Can't comment on accuracy as I'm no expert but very happy with the result
-
Dalek Hal 312
Great file, easy to print
-
doctorone 3
Great plan but the pivot does not print as it is not complete like the eye stalk
-
-
Download Statistics
-
Recent File Comments
-
-
By WhosWho · Posted
@RepeatedMemeDid you change something? I haven't touched anything. -
By RepeatedMeme · Posted
@WhosWho @dalekray It's only showing an update because the (written) details were edited. -
-
By life size · Posted
I printed mine in PTEG, 235 nozzle, 60 Bed , no supports and it printed with no mess at all. I ran it at a 40 percent print speed, and the orientation was large cup facing down on my print. -
By John · Posted
See this FAQ topic for more on Downloads availability: -
By ChristmasDalek · Posted
Welcome to the forum! Sorry you have encountered a problem... While waiting for someone who knows more about the downloads section than I do to answer, you may find the explanation in @Johns answer to this thread: Be well, Kathy -
By tardis112 · Posted
Why am I not permitted to download this? -
By Mark Casto · Posted
This is such a useful file for the eye it is perfect for adding a fish tank led inside and looks great thank you. -
By DarthCranium · Posted
ok @Bodule. i apologize if i caused any issue. -
By Bodule · Posted
Hi @DarthCranium Can I suggest that you ask your question in the 3D Printer Discussions section of the forum please? https://www.projectdalek.com/index.php?/forum/209-3d-printer-discussions/ That section itself may be worth a read through, as is @ChristmasDalek's post above yours 👆 here as it may provide additional useful information on how to use the forum. -
By DarthCranium · Posted
What is a good size of 3D printer youd recommend if i wanted to make a dalek of my own? please let me know when able. Thanks -
By Dalek-Nik · Posted
Moflash lenses appear to be slightly difficult these days. the best bet in my opinion is 3D printing them. there are many accurate models here that can be printed on any FDM printer you can find. there is a chance that you can find the lenses online to buy, but those sites can be slightly sketchy. depending on the filament you buy and the printer you have/find, they can be produced fairly accurately. filament can come as cheap as 17 dollars, but do keep in mind that they can some
-
-
Highest Rated Submitters
No ratings this week.
No ratings this month.
-
1
-
2
-
3
-
4
-
5
-
1
-
2
-
3
-
4
-
5
-
-
Current Donation Goals
-
Finance the Forum Hosting 2024Raised £113
-
-
Top Templates
-
Free
-
Free
-
Free
-
Free
-
Free
-
