-
Registration
Please register an account to access the Forum topics and features.
An Active Membership subscription gives you access to extra features and exclusive content!
Choosing Active Membership is a great way of supporting the community and showing your appreciation for our resources.
Please note that you need to register BEFORE you can use Facebook, Twitter or Google as a sign in method.
Files For 3D Printing
Files that can be used to for 3D printing physical versions, using your own printer or a service such as Shapeways etc.
Note that files for CNC and laser cutting can be found in their own sub-section, inside.
247 files
-
Free
Gazing Globe Drill Box
By trickster
This is a jig I made to drill a pilot hole in a 10cm gazing globe. The globes I used were Rome brand purchased thru Amazon. Each had a single hole already drilled. This jig allowed me to drill a matching hole directly opposite.
The base has leaves which can be clamped to the drill press table. It also has a peg which fits the existing hole in the globe. I clamped down the base, fitted the globe to the pin in the base, pushed the cylinder down over it and then the lid. The lid has a center hole.
There's also test cylinder file which is only 5mm tall. If you want to use this jig I suggest you first print the test cylinder and make sure it is the right size for your globe. It should fit very snugly.
156 downloads
(0 reviews)0 comments
Submitted
-
Free
Heronrib Panels
By WhosWho
3D printable panels based on Heronrib matting for use in NSD neck bins. Includes two different versions with different gap alignments.
148 downloads
(0 reviews)0 comments
Submitted
-
Free
NSD Eyestalk Pivot
By cdngoose
This NSD Eyestalk pivot is similar to my Shawcraft version ( Thanks to Phil for Drawing this up for me)
NSD Eye pivot
1" hole for eyestalk shaft
Smaller centered 3/8ths hole for threaded bar
Slot for threaded bar nut.
Hole through the backside to the slot for wiring.
3/8ths hole centered for pivot
146 downloads
-
Free
NSD Neck Matt
By elembivos
STL files to print replica pool matt for an NSD neck. Modeled after actual pool matting used on my first NSD build, which was not authentic Heronrib/Heronair. Just the closest equivalent I could find at the time. Designed to glue into a 3D printed set of neck rings. 3 levels are designed smooth where they will mate to the neck rings to provide more surface for gluing. You may need to trim here and there to fit your neck rings.
145 downloads
-
Free
Printable Oil Seal Surrounds and Hemispheres (Glowing?)
By Kresty
My take on oil seal surrounds and hemispheres... I'm not sure these are practical as it takes an hour to print a surround and a couple for a hemisphere, but here they are...
The reason I did this was because brialath has talked about a Disco Dalek and I wanted to see if WS2812B LEDs would be able to light a 100mm hemisphere. Since I made the hemisphere, I decided a mount for the aforementioned LEDs built into the surround might be good, and the traditional center bolt doesn't really work because the LED needs to be there.
Since I could I also made a solid hemisphere that might print better, and a surround with a centered bolt hole for an M4 bolt, and a little block to keep the bolt head from turning. I considered glynharper's surrounds, however I wanted an exact fit for the hemisphere I'd made, and I wanted a enough room for a 12-14mm washer to distribute the load. So that meant I needed a block to hold the M4 bolt head, the recessed version wouldn't work. Also, of course I needed a version with a spot for the LED in the middle.
The surrounds are intended to fit exactly in the middle of the hemisphere. They probably need some sort of adhesive, but for my printer it was a really close fit.
Since normal humans could reuse these for xmas ornaments or something, I put them on Thingiverse, with more info... http://www.thingiverse.com/thing:726897 (including the openscad & sketchup files for them).
138 downloads
-
Free
Ferrain - Dome Rotation Involute Spur Gear V5
By Ferrain
Dome Rotation Involute Spur Gear V5
I set up a virtual Windows 7 machine, with a trial copy of Sketchup Pro & downloaded the actual DXF files from the Involute Spur Gear Builder & after some work Saturday morning produced a totally new gear configuration.
Sunday
I completed two 45 degree sections successfully - The 45 degree files are included but were cut into sections with Sketchup without Netfabb.
I completed three 90 degree sections (with only one aborted print) but again were cut into sections with Sketchup without Netfabb
These NEW 90 Degree files are based on the original DXF files\Sketchup model I used, only with holes removed\repositioned locking lugs & sliced via Netfabb.
Addendum
The prints all fitted tightly against my Rockler\Lazy Susan Bearing, but possibly due to mix & matching of 45 & 90 degree sections or not using Netfabb as a slicing tool, I found I had a small gap, please adjust\check the Internal diameter & I have included the Sketchup file with a complete ring, the exploded 45 degree sections & the cog, which you can tailor for your own motor\drive configuration.
Height has been increased to 10mm - Each section typically took 75 minutes to print at a medium resolution settings on a Makerbot Replicator 2 at 8mm height.
136 downloads
(0 reviews)0 comments
Submitted
-
Free
Moflash Lens
By WhosWho
A hi res STL based on the Moflash lenses used New Paradigm and New Series Daleks.
135 downloads
-
Free
Eye design
By MechDesign
This is a design I did for Nigel and his new dalek that will be named Avo.
130 downloads
-
Free
Neck Block Detail
By hallam
NSD Neck Block Detail as STL file suitable for digital printing.
The inside of the neck block is hollowed out to minimize use of material. Wall thickness is 1mm.
127 downloads
(0 reviews)0 comments
Submitted
-
Free
"Eve of the Daleks" Gatling Gun for NSD. Full Size, Rotating
By threegringos
This is the NSD "Gatling Gun" weapon as seen on the trailers for the 2022 New Year's episode "Eve of the Daleks".
This 3D model was made before the episode aired, so the scren shots were very limited. It looks accurate to my eye, however more details may become apparent once we get to see the entire episode.
I used Fusion360 to create this model. It's split into multiple parts for ease of printing.
You will need to provide a 25.4mm (1 inch) diameter pipe for the arm, and also mount a suitable 102mm (4 inch) ball-joint. I always use magic 8-ball toys for my ball joint.
The eight small pipes coming out of the rear of the gun part are 6mm diameter. You can either print them from my files, or optionally use stainless steel drinking straws, cut to length.
I did include an internal gear in the main body of the gun, and an additional pinion gear in case somebody wants to motorize the rotation of the weapon. I haven't had time to figure that out yet.
127 downloads
-
Free
NSD screw-on Hemi.stl
By DalekDucky
NSD screw-on Hemi
Here is my first dive into creating an STL
Because I want the ability to change my Hemi's at Christmas to have lights inside of them, Dalek camouflaged as a Christmas tree, I created this Screw on Hemi holder.
Two parts,
Internal bracket has three holes for screws, center could be removed but I wanted it to ensure the hemi was centered, it also has a bracket for my LED lights as seen in picture.
Outside bracket is simply a bracket to glue on the Hemi using two parts Christmas ornaments and then simply screw it onto the internal bracket.
Could be handy for quick replacement option of hemi
Hope it helps someone else
Oh! The screw holes are for 3/16.
DalekDucky
125 downloads
-
Free
Mk 3 Dalek Eyestalk - for my uploaded eye STL's.
By ansonjames
Eyestalk for my uploaded eye STL's.
Print Eye stalk bottom and eye pivot in the orientation it's presented in WITH supports, at least 20% infill and three perimeters is good.
No supports required for eye stalk top, it's been tested with the properly sized transparent acrylic tube which fits perfectly and has no play.
No glue required, just an M10 thread bar with two nuts for top and bottom.
Fire me a PM if you have an questions!
118 downloads
(1 review)0 comments
Updated
-
Free
Gun Box Detail
By hallam
NSD Gun Box Detail as STL file.
Back of the piece is hollowed out to minimize use of material. Wall thickness is 1 mm. I paid $25 for printing and after sanding and filling, glued the result to a piece of acrylic to give it a flat base to make moulding easier.
117 downloads
(0 reviews)0 comments
Submitted
-
Free
Dalek MK3 Slats
By Ferrain
Dalek MK3 Slats.
Suitable for 3D printing or on a CNC machine - Holes are 2mm in diameter.
Accurate as per the latest MK3 Plans - Caveat I always assumed the slats were metal like the collars, not acrylic consequently the thickness reflects the width of the collars\belts (Unless John & co can update me).
It looks as though these will be time intensive to 3D print (2.5 hours per large slat), if you are using a glass build plate (Like moi), a nice smooth glossy finish should be produced.
Update - Additional info & picture.
First Small Slat Printed (It lifted a bit on the build plate).
New Sailfish firmware installed away from stock Makerware gives additional information as to the amount of material (Height increased to 2.5mm with settings at 0.1mm layer height & 8% Infill) - 1 hour 21 mins build time, 6M of filament.
116 downloads
(0 reviews)0 comments
Updated
-
Free
Classic Dalek Pivot
By Ferrain
If printing the Genesis 5.5" Tapered Eye Stalk - The pivot should not be printed first in the event that the pivot insert shears & can't be refitted.
Print with a raft to allow ease of joining the halves.
PivotJan8FFV4.stl - Flat faced (no insert for eye stalk) with threaded bar channel - Choose this one if you have a eye stalk that will not fit into the 1" insert (or if the insert has sheared during the printing).
PivotJan8INSV4.stl - Insert 1" diameter 1.1cm depth hole to accommodate straight or tapered eye stalks.
Print the guide 4mm diameter pin for ease of assembling the two halves if required.
Print time on standard profile MB Replicator 2 should take about 2.5 - 3 hours & use 2.5 39g (0.09IIb) on standard quality print settings for each half.
114 downloads
(0 reviews)0 comments
Updated
-
Free
NSD sphere for gun or plunger
By Mr zen
NSD gun / plunger barrel sphere the hole can be altered to suit the diameter of the tube your are using for your build. when fitted i used felt to stop any friction when in place
113 downloads
-
Free
70's Dalek Eyes 1 - Day of the Daleks high poly STL.
By ansonjames
No supports required except for the back of the eye, remove supports on this part and insert the ring which is for aligning the front and the back of the eye.
If the part layout is too big for your print bed just separate the parts in printing software or import into Microsoft 3D builder (free software) edit file and split keeping both top and bottom.
Parts are oriented for best printing speed and quality - 20% infill, 3 perimeters recommended. Send me a PM if you need assistance!
11MM diameter hole is for the eye stalk/pivot files which I'll upload soon, the finished prints are kept together with an M10 threaded bar and nuts.
111 downloads
(0 reviews)0 comments
Updated
-
Free
Oil Seal with centered secure
By cdngoose
This Oil seal is like Kresty,s file also found in this section, however I was not after a Disco version of Dalek ( at least not yet, I do have future plans for Kresty.s oil seal surround) so it has a centered secure piece and a bit thicker edge. I have printed close to 200 of these now and they are sized to fit the 100 mm fillable Christmas ornament.
(future plans - I will use Krestys oil seals for two Daleks that will be replacing my street lamps on either side of my driveway, I will also add an arduino with motion sensor so the dome will follow anyone walking by the end of my driveway) I live in an Amish community and they already think I'm Satan, might as well prove it! :-)
cdngoose
110 downloads
(0 reviews)0 comments
Updated
-
Free
mk1 and 2 dome lights
By Sparky_Butane
Included are a solid and shelled files. They are as accurate as I could make them so please message me with any comments or questions.
Thanks and Enjoy
108 downloads
(0 reviews)0 comments
Submitted
-
Free
Classic Dalek Appendage Seismic Detector
By Luke S
A Zip File of the whole items is in the download to save up download room.
There are 7 parts, the Bottom Half, numbers, the top, white band, outer gyro ring, inner gyro ring, and Diel. There are already to holes in the print for the dial thingy that spins and the rods that connect to the gyro. The holes for the rods in the print are 4 mm in diameter. US Also You may need to add washers around the pins to stop the rings from sliding off. Thanks to @James O and @Dave'O for there estimated gused blueprints.
IF You have Downloaded any of my Prints please Pm if I have added or edited it, so i can send you the newest copy.
Unauthorized sales and distribution, in any format, is strictly prohibited.
Print Settings
Printer brand:
Creality
Printer:
Ender 3
Infill:
100%
Filament_brand:
Filament_color:
white, Black
Filament_material:
PLA
107 downloads
-
Free
NSD Eye Front
By Mr McGoo
I created my own CAD files for the NSD eye to print because I wasn't happy with any that I found, they all needed some unsightly supports.
I designed these to be easy print (I did mine on an Ender 3, came out great) The front section doesn't need supports, orientate it so the front section faces up and it'll print nicely. The back section needs a support in the middle to print the stem, which broke off easily for me. Tolerances are pretty tight and will need some light sanding to make it a little looser. Then you just have to drill your holes for your allen bolts and you're good to go!
106 downloads
(1 review)0 comments
Submitted
-
Free
mk3 or "Egg Cup" lights
By Sparky_Butane
Here are the files for 3D printing the mk3 dome lights. If you have any questions or comments please message me.
Thanks and Enjoy
102 downloads
(0 reviews)0 comments
Submitted
-
Free
2005 Dalek Eye Discs
By jbourd
Here is all three different size eye stalk plates for the 2005 Dalek.
Hope they work well, they were found on thingverse.
102 downloads
-
Free
NSD Plunger EMA Parts
By DalekDucky
There are lots of great NSD plungers in the PDF, this ZIP file is of all the various EMA parts pre cut to build your own Plunger.
This also allows you to decide if you want the two "cuts" on the plunger to be aligned or not.
Modifications are:
added a groove in VHH-450 tp allow to center VX-225, added grooves in VHD-475 to center VHH-450 with minimal filler Added small cut at top of VHH-425 for more surface when affixing VT-32 Optional, created a spacer to place between the two VX-40 Optional, insert for the arm to help affix to your arm
You will need to print 4x KW-12 and 2x VX-40
Of possible use, As I am still calibrating my printer, to make the sanding easier, I Printed
VHH-400 and VHH-425 so the inside would be facing up to make sanding from support easier, and KW-12 were flat
Enjoy and Happy Building
101 downloads
(1 review)0 comments
Updated
-
Free
(0 reviews)0 comments
Submitted
-
Top Downloads
Week
-
Free
-
Free
-
Free
-
Free
-
Free
Month
-
Free
-
Free
-
Free
-
Free
-
Free
Year
-
Free
-
Free
-
Free
-
Free
-
Free
All Time
-
Free
-
Free
-
Free
-
Free
-
Free
-
-
Recent File Reviews
-
Michael56 2
I'm in my late 60's. I live in Australia and have always enjoyed Doctor Who from the very first episode aired here around 1965 when I was 9 years old. Thought how amazing it would be to have a Dalek but had no idea how or where to even begin UNTIL I came across this site. Thanks for giving me the opportunity to at least be able to start on a Dalek build and will detail my progress as it goes along.
-
Mark Sheriff 6
Excellent , looks great and very well designed , well thought out . thank you
-
Marc Harris 54
I'm in my 50s and have since I was a boy watching Dr Who in the 70s always dreamed of making a Dalek for fun, now I have the time and resources, along with your forum's help it's time to live that dream.
I have watched some of the members videos, and I am very impressed with what I have seen.
Long live the Who verse.
I will document my progress and share any innovations I make
-
Chris R 25
Great set of models that printed and fitted together really easily. Can't comment on accuracy as I'm no expert but very happy with the result
-
Dalek Hal 312
Great file, easy to print
-
doctorone 3
Great plan but the pivot does not print as it is not complete like the eye stalk
-
-
Download Statistics
-
Recent File Comments
-
-
By WhosWho · Posted
@RepeatedMemeDid you change something? I haven't touched anything. -
By RepeatedMeme · Posted
@WhosWho @dalekray It's only showing an update because the (written) details were edited. -
-
By life size · Posted
I printed mine in PTEG, 235 nozzle, 60 Bed , no supports and it printed with no mess at all. I ran it at a 40 percent print speed, and the orientation was large cup facing down on my print. -
By John · Posted
See this FAQ topic for more on Downloads availability: -
By ChristmasDalek · Posted
Welcome to the forum! Sorry you have encountered a problem... While waiting for someone who knows more about the downloads section than I do to answer, you may find the explanation in @Johns answer to this thread: Be well, Kathy -
By tardis112 · Posted
Why am I not permitted to download this? -
By Mark Casto · Posted
This is such a useful file for the eye it is perfect for adding a fish tank led inside and looks great thank you. -
By DarthCranium · Posted
ok @Bodule. i apologize if i caused any issue. -
By Bodule · Posted
Hi @DarthCranium Can I suggest that you ask your question in the 3D Printer Discussions section of the forum please? https://www.projectdalek.com/index.php?/forum/209-3d-printer-discussions/ That section itself may be worth a read through, as is @ChristmasDalek's post above yours 👆 here as it may provide additional useful information on how to use the forum. -
By DarthCranium · Posted
What is a good size of 3D printer youd recommend if i wanted to make a dalek of my own? please let me know when able. Thanks -
By Dalek-Nik · Posted
Moflash lenses appear to be slightly difficult these days. the best bet in my opinion is 3D printing them. there are many accurate models here that can be printed on any FDM printer you can find. there is a chance that you can find the lenses online to buy, but those sites can be slightly sketchy. depending on the filament you buy and the printer you have/find, they can be produced fairly accurately. filament can come as cheap as 17 dollars, but do keep in mind that they can some -
By Chris R · Posted
Thanks for uploading these files. Printed really nicely with the odds and sods of filament I had around and very pleased with it, haven't done any tidying up or painting but it looks great as-is.
-
-
Highest Rated Submitters
No ratings this week.
No ratings this month.
-
1
-
2
-
3
-
4
-
5
-
1
-
2
-
3
-
4
-
5
-
-
Current Donation Goals
-
Finance the Forum Hosting 2024Raised £113
-
-
Top Templates
-
Free
-
Free
-
Free
-
Free
-
Free
-
