Files For 3D Printing

247 files

1. 

   Free

   Necros/Renegade BASE (only) For Dome Lights

   By Luke S

   Took a long time and labor... just to get the slits in the bottom part. I used the Plans from the Necros and Renegade Daleks. Some Sanding may be needed after printing. It would be best for you to make a cast of the light part, and when you get those cast maybe you could sell them in the Sec shope for others 🤔
   These Lights work perfectly for the Renegade Supreme, but you will need a band around the bottom. 
   Print Settings
   Printer brand:
   Creality
   Supports:
   Yes
   Resolution:
   0.1mm
   Printer:
   Ender 3
   Infill:
   100%
   Filament_brand:
   Filament_color:
   Translucent white, Black
   Filament_material:
   PLA
   

   59 downloads

      (0 reviews)

   8 comments

   Updated April 7, 2020

2. 

   Free

   Marx_BumpNGo_parts

   By LabRat

   STL for replacement plunger, gun, and eye-stalk, for the 6.5" (1974) Bump and Go toy. Used online images for reference and scale, as I had no access to originals to measure. Photo shows first print attempt (with some sagging, as I didn't have enough supports in place).  Also included are versions of the laser and eye-stalk with a hole ready to accept 3mm acrylic rod (in case you want to add additional "blinky/flashy" effects.  
   
   Post pics if you print these for you Dalek.
   

   17 downloads

      (0 reviews)

   0 comments

   Submitted October 11, 2022

3. 

   Free

   Renegade Dalek Styled 3D Print

   By Zach

   The body of a dalek loosely based on the Renegade dalek. The whole thing can be printed in one go. I printed it at 50% scale with 20% infill and it came out great. The three holes are for the eye and turrets; I haven't yet finished modeling them, but when I do I will add the files here.
   

   6 downloads

      (0 reviews)

   0 comments

   Submitted October 6, 2022

4. 

   Free

   NSD 'Death-Squad' Dalek claw - "Revolution of the Daleks". Fully operational

   By threegringos

   This is my NSD 'Death Squad' claw as seen on the Daleks in the 2021 New Year's special "Revolution of the Daleks".
   
   I made this originally for my own Dalek, (Dalek Axel).  I've been constantly getting messages through my Instagram from people who want a claw, so I thought I'd release it here on Project Dalek for the community to use.
   This 3D model was developed solely from screenshots and promotional images.  It looks accurate to my eye, and some deliberate (but small) compromises were made to simplify the 3D printing process.
    
   I used Fusion360 to create this model.  The claw is split into multiple parts for ease of printing.
   The ZIP file contains photos and instructions.
    
   NOTE:
   For assembly, you will need some 3mm diameter stainless steel rods or dowels for pivots.  I bought a pack from Amazon, and cut them down to size.
   You will need to provide your own arm (and Dalek) to mount the claw onto.  The claw will fit a 25.4mm (1 inch) diameter pipe.
    
   Enjoy!
    
   

   77 downloads

      (1 review)

   0 comments

   Submitted October 2, 2022

5. 

   Free

   Reworked NSD moflash cage.

   By bappi

   I downloaded the zip file from  Ultrastar's downloads and noticed that 2 of the files were labelled wrong so corrected that with these files here, I also noticed when i had printed the base that when screwed on tight there was at least 5 mm gap around the bottom so i resliced the file and now it has a nice flat base i then drilled 2 holes through the base and bolted onto the dome.. I bought 2 twist fit bulb holders as u can see in the pics, this fits through the dome nicely and fits inside the mosflash lense very snug, to change the bulb just unscrew the cage.
   

   222 downloads

      (0 reviews)

   0 comments

   Submitted September 18, 2022

6. 

   Free

   NSD: Light Cage

   By Ultrastar

   NSD: Light Cage
   By: Ultrastar
   Intended for Dalek builders out there with the ability to 3D print models. This is a 3D model of the NSD Light Cage. This model was created with the purpose of 3D-Printing. However, with this being a 1:1 scale and 100% accurate model it can also be used as a reference for your own builds. Feel free to ask questions about this model as you see fit.
   

   775 downloads

      (4 reviews)

   12 comments

   Submitted April 25, 2017

7. 

   Free

   Renegade Dalek Plunger

   By DrBullas

   Just printed off a file a work colleague created for me from the Renegade Dalek Plans plunger drawing, printed in semi flexible black it looks pretty good! Printed off nice a slow didn't need supports.
   

   11 downloads

      (0 reviews)

   0 comments

   Submitted September 12, 2022

8. 

   Free

   Goon X Eye - As Per PDF Plans.

   By ansonjames

   Supports required front/back of the eye, remove supports on these parts and insert the ring which aligns both parts.
   If the part layout is too big for your print bed just "select all" and "ungroup" in Microsoft 3D builder.
   Parts are oriented for best printing speed and quality - 20% infill, 3 perimeters recommended. 
   11MM diameter hole is for the eye stalk/pivot files which are located here;
    
   The finished prints are kept together with an M10 threaded bar and nuts.
   
   

   19 downloads

      (0 reviews)

   0 comments

   Updated August 14, 2022

9. 

   Free

   Accurate plunger - high poly

   By ansonjames

   60's/70's Style plunger created using the newer plans. Can be printed with FDM or SLA.
   I added a rod at the bottom to slide onto the last stage of the arm, if you don't intend to use this part then you can import into Microsoft 3D builder, go to edit and split model.
   

   92 downloads

      (0 reviews)

   2 comments

   Submitted February 20, 2021

10. 

    Free

    Dome sander

    By kevin pedley

    This is a sanding pad that is concave on the sanding face - to match the radius of the original Shawcraft domes.
     
    It allows finish sanding without loosing the profile. 
     
    After printing (recommend printing it on it's edge to get a better concave profile) strips of wet and dry are glued to the surface, and away you go.
     
    Sand with a  circular motion. It maintains the edge between the radius and the taper of the dome.  
    

    35 downloads

       (0 reviews)

    0 comments

    Updated July 17, 2022

11. 

    Free

    Dalek Gatling Gun

    By RattyVulcan

    These files allow you to build a version of the Gatling Gun which includes integrated pistol grip and a housing for a motor and electronics to replicate the lights and spinning effect of a 'real' gatling gun as it slows due to friction.
     
    More details can be found here: 
     
    

    313 downloads

       (1 review)

    0 comments

    Submitted June 28, 2022

12. 

    Free

    Louis Marx Bump and Go Toy Dalek

    By erichdalek

    This is a model of the Louis Marx Bump and Go Toy Dalek of the 60's, as used in the production of Evil of the Daleks per information from this gallery entry and this BBC photo.
     
    Provided is:
    -.SLDPRT of the whole thing, for your personal improvements or modifications
    -.STL of the whole thing
    -.STL's of it with the eyestalk and appendages in separate files for you to glue on
     
    Let me know any ways I could better the screen-accuracy or proportions.
     
     
    

    307 downloads

       (0 reviews)

    1 comment

    Submitted August 7, 2021

13. 

    Free

    NSD Cowl Quadrants

    By Pgordon

    This is the NSD Cowl 1.0.0 By Macropod80, but split into 4 roughly equal sized quadrants which can be printed on printers with a much smaller build area. I created these splits for my Flashforge Adventurer 3 which only has 150x150x150 build area, and they print fine, and join together pretty well with nice tight seams. Someone more proficient at 3D modelling than I could perhaps improve these models by adding some alignment/reinforcing tabs along the joins to aid with accurate assembly and strengthen the joins in the assembled piece. In my case I joined the pieces with superglue and held them together by hand while the initial bond formed.
     
    Whilst the seams are fairly tight & neat, they're not invisible, so the completed assembled cowl will still need filling, sanding & painting. The parts need to be printed with supports, which are not in these model files, you'll have to add them in your slicer.
     
    I printed these in PLA with 0.2 layer height, and each quadrant is roughly a 16 hour print at the highest quality on my machine.
     
    Hope this helps someone!
    

    238 downloads

       (1 review)

    1 comment

    Submitted October 28, 2020

14. 

    Free

    NSD Plunger EMA Parts

    By DalekDucky

    There are lots of great NSD plungers in the PDF, this ZIP file is of all the various EMA parts pre cut to build your own Plunger.
    This also allows you to decide if you want the two "cuts" on the plunger to be aligned or not.
     
    Modifications are:
    added a groove in VHH-450 tp allow to center VX-225, added grooves in VHD-475 to center VHH-450 with minimal filler Added small cut at top of VHH-425 for more surface when affixing VT-32 Optional, created a spacer to place between the two VX-40 Optional, insert for the arm to help affix to your arm  
    You will need to print 4x KW-12 and 2x VX-40
     
    Of possible use, As I am still calibrating my printer, to make the sanding easier, I Printed
    VHH-400 and VHH-425 so the inside would be facing up to make sanding from support easier, and KW-12 were flat  
    Enjoy and Happy Building 
    
    

    101 downloads

       (1 review)

    0 comments

    Updated January 10, 2022

15. 

    Free

    Full Scale Shawcraft Dalek Dome Model and Negative

    By Omeganinjaboy

    The dome is based on the Version 3.1 Movie plans (so the eye slot is higher than other classic domes), though the negative and back half files are consistent with other classic domes dimentionally. You could just print two back halves if you do not want a movie dome and cut the eye slot yourself. I would advise you consult the dome dimentions in the Version 3.1 Movie plans and compare them against the dimentions of your own plans if you are building a different classic dome.
     
    This is a 3D printable Dalek dome model that has a curved eye slot rather than a rectangle extruded one making it more accurate to the real thing (It took quite a while to figure out how to make a hole based on a curved measurement in CGI). The front and back halves are provided, but you will have to slice it up if the model is bigger than your printer's build volume. The skinny dome is half an inch (1.27cm) thick and the normal one is one inch (2.54cm) thick. There are lower poly and higher poly (HD) variants of most files. A negative of the dome is also included for you want to use however you wish.
    

    336 downloads

       (0 reviews)

    13 comments

    Updated January 4, 2022

16. 

    Free

    NSD Neck Matt

    By elembivos

    STL files to print replica pool matt for an NSD neck.  Modeled after actual pool matting used on my first NSD build, which was not authentic Heronrib/Heronair.  Just the closest equivalent I could find at the time.  Designed to glue into a 3D printed set of neck rings.  3 levels are designed smooth where they will mate to the neck rings to provide more surface for gluing.  You may need to trim here and there to fit your neck rings.
    

    145 downloads

       (0 reviews)

    9 comments

    Submitted February 25, 2021

17. 

    Free

    Exploded NSD dome for 3D printing

    By cjorgensenmd

    This in my NSD dome sliced into manageable files for 3D printing. Each section is still fairly large. you will need at least 200mm x 200mm print area, but once everything is printed, they can be attached to a lasercut base and then glued together for a very accurate NSD dome which will require very little finishing before a fiberglass mold is made. I have included both the raw solidworks files as well as the STLs in case anyone would like to make edits. I will edit this post once I have all 16 sections printed. I have two so far and they each took about 14 hours to finish, so this is a patient process.
    

    370 downloads

       (0 reviews)

    11 comments

    Submitted July 4, 2017

18. 

    Free

    Oil Seal Surround for 100mm hemis

    By napier1973

    ok i jumped on cad and changed the surround a little so it fit the 100mm hemisphhere only changed is the walls thicker.
    

    82 downloads

       (0 reviews)

    0 comments

    Submitted September 19, 2021

19. 

    Free

    Alternative Dome Light Cages for use with Quilted Mason Jars

    By anthony lathrop

    Instead of the canonical MoFlash dome light lenses, my son and I used 1/4 pint quilted Mason jars (widely available in the US, not sure about elsewhere).
    The jars are a bit shorter and squatter than the MoFlash lenses and they have a diamond embossed pattern instead of the vertical grooves - but they look pretty close and behave  similarly when lit from inside.
    These files comprise dome light cages that fit the Mason jars.
    The .stl files are low poly.
    Also including the solidworks files so you can make your own high poly .stl files if desired.
    

    42 downloads

       (0 reviews)

    0 comments

    Submitted August 29, 2021

20. 

    Free

    NDP Telescoping Joint

    By bryanxiii

    This is the joint you see at the midsection of the telescoping plunger arm.
    Measurements based on NDP Plans. 
     
    I added a tube at the bottom to push into the larger portion of the plunger arm to help secure it and have something to glue to.
    The OSD of addon tubing is 27mm.  
    The ISD overall is 18mm to give 1mm of clearance on the 17mm OSD telescoping tube.  
     
    Print orientation: I would suggest printing this with the tapered section down with a build plate.
     
    Density: My suggestion on this is 100% mainly to give strength to the section where it gets glued on.   
     
    If you need an alternative sizing version PM @bryanxiii 
    

    17 downloads

       (0 reviews)

    0 comments

    Submitted August 24, 2021

21. 

    Free

    NSD Eye Front

    By Mr McGoo

    I created my own CAD files for the NSD eye to print because I wasn't happy with any that I found, they all needed some unsightly supports.
     
    I designed these to be easy print (I did mine on an Ender 3, came out great) The front section doesn't need supports, orientate it so the front section faces up and it'll print nicely. The back section needs a support in the middle to print the stem, which broke off easily for me. Tolerances are pretty tight and will need some light sanding to make it a little looser. Then you just have to drill your holes for your allen bolts and you're good to go!
    

    106 downloads

       (1 review)

    0 comments

    Submitted August 11, 2021

22. 

    Free

    NSD Eye Back

    By Mr McGoo

    CREATOR's EDIT: My apologies, I only just realised this has 8 rods, not 12 going around the eye. I'll leave the files up for now in case anyone wishes to modify them, as I don't have the time right now. My plan is to sand off the rods printed on the eye, and make/glue the vessel tubing as a separate part so to not bin the one I currently printed. Just wanted to be fully transparent about this mistake!
     
    I created my own CAD files for the NSD eye to print because I wasn't happy with any that I found, they all needed some unsightly supports.
     
    I designed these to be easy print (I did mine on an Ender 3, came out great) The front section doesn't need supports, orientate it so the front section faces up and it'll print nicely. The back section needs a support in the middle to print the stem, which broke off easily for me. Tolerances are pretty tight and will need some light sanding to make it a little looser. Then you just have to drill your holes for your allen bolts and you're good to go!
    

    79 downloads

       (0 reviews)

    0 comments

    Updated August 13, 2021

23. 

    Free

    NSD screw-on Hemi.stl

    By DalekDucky

    NSD screw-on Hemi
    Here is my first dive into creating an STL
    Because I want the ability to change my Hemi's at Christmas to have lights inside of them, Dalek camouflaged as a Christmas tree, I created this Screw on Hemi holder.
     
    Two parts, 
    Internal bracket has three holes for screws, center could be removed but I wanted it to ensure the hemi was centered, it also has a bracket for my LED lights as seen in picture.
    Outside bracket is simply a bracket to glue on the Hemi using two parts Christmas ornaments and then simply screw it onto the internal bracket.
     
    Could be handy for quick replacement option of hemi
    Hope it helps someone else
     
    Oh! The screw holes are for 3/16.
     
    DalekDucky
    

    125 downloads

       (0 reviews)

    3 comments

    Updated October 10, 2022

24. 

    Free

    Shawcraft Eye Control

    By kevin pedley

    This is a copy of the Shawcraft eye control. The diameter of the "pulley" is 102mm, the same as the eye pivot so should give a 1:1 ratio when rotating the control. There are 4 holes around the outside of the control 8mm in diameter - idea if you have some 8mm dowel left over from the neck struts. The centre hole is 8mm, and the control lock is designed to take an 8mm nut with plastic insert. 
    

    61 downloads

       (0 reviews)

    0 comments

    Updated July 19, 2021

25. 

    Free

    Imperial Dalek: Eye Stalk

    By Necrosis

    This is a download for the Imperial Dalek eye stalk. The files are in .stl format making them easy to 3D print or to use as digital references/models. These parts are 1:1 scale and match the most recent revision of the Imperial Dalek plans making it plug and play to print or easy to scale to your Daleks needs. I personally 3D printed these units to create a mold that allows me to cast the part with perfect detail. You can achieve the center reflective disc by printing the part and then covering it with a reflective film as shown in the screenshots above. However, I prefer the none reflective disc on my personal Dalek build. The parts look great as 3D prints alone with some filler and primer and detail work. Recommend printing these parts slow and precise at 15% infill for best results.
    (Would love to see any print results from anyone who chooses to share on this thread)
     
    Details:
    Scale - 1:1 (In compliance with Imperial Dalek Plans Version 3.5)
    Parts included in this download - Eye Stalk * Eye Piece * Reflector * 4 Stalk Discs * Eye Pivot
    NOTE: For ease of assembly, parts have a 0.5mm to 1mm tolerance. The eye Pivot has a 12mm (1/2") hole in the center for a bolt and a larger hole on the backside that can be used to attach a control rod for the eye stalk.
     
    I will keep these files up to date and if you have any suggestions or find any errors please let me know so that I may update the parts.
    

    49 downloads

       (0 reviews)

    1 comment

    Updated February 8, 2022