Files For 3D Printing

246 files

1. 

   Free

   Full Scale Shawcraft Dalek Dome Model and Negative

   By Omeganinjaboy

   The dome is based on the Version 3.1 Movie plans (so the eye slot is higher than other classic domes), though the negative and back half files are consistent with other classic domes dimentionally. You could just print two back halves if you do not want a movie dome and cut the eye slot yourself. I would advise you consult the dome dimentions in the Version 3.1 Movie plans and compare them against the dimentions of your own plans if you are building a different classic dome.
    
   This is a 3D printable Dalek dome model that has a curved eye slot rather than a rectangle extruded one making it more accurate to the real thing (It took quite a while to figure out how to make a hole based on a curved measurement in CGI). The front and back halves are provided, but you will have to slice it up if the model is bigger than your printer's build volume. The skinny dome is half an inch (1.27cm) thick and the normal one is one inch (2.54cm) thick. There are lower poly and higher poly (HD) variants of most files. A negative of the dome is also included for you want to use however you wish.
   

   336 downloads

      (0 reviews)

   13 comments

   Updated January 4, 2022

2. 

   Free

   NSD Cowl

   By trickster

   Here is a set of models for creating an NSD cowl. Jbourd was kind enough to gift me with a 3d model of a complete Dalek dome and cruel enough to ask if I could separate out the cowl. It took a while but I managed to remove the dome and leave the cowl intact. Of course it is far to big to fit on my build platform. So I tried cutting it in half vertically. Each piece could only fit my build space in a few orientations. And due to the size and nature of the parts, they all warped beyond use. I wasted nearly a kg of filament on failed attempts. I decided to split it into quarters. This allowed for smaller parts which would fit flat and any warp would be to the thickness. Thought I had it nailed, but the thickness was warped enough so that the towards the back of the cowl the opening was too small to fit the eyestalk pivot. So I added a shim to compensate.
    
   I have been using 3d Builder which is included with Windows 10. It has issues. For whatever reason I was able to separate out and save three out of four quarter pieces but the fourth would not save no matter what I did. So instead I used Replicator to mirror the pieces along the X-axis. That is why only right side parts are included. You have to use your build software to mirror them for the left side parts.
    
   I've included the full cowl model in case you want to slice and dice it on your own. I've included the shim I used and a long peg to use with it. I suggest building out the four main parts and see if you need it.
    
   Also the bottom parts had an issue with one corner pulling loose from the build plate and warping the holes. So I put a throw away block next to that corner to hold it down.
    
   I printed everything at 10% fill .2mm thickness. Use full support and raft for the main pieces but not pegs and shim.
    
   One thing I did not expect but really like is that in producing the curves, the printer leaves a pattern which is similar to wood grain. This is another reason why I included parts for only one side. By mirroring the parts the grain pattern is symmetrical.
    
   Here's some pics. You can see the grain effect.
   
   .
   

   328 downloads

      (0 reviews)

   7 comments

   Updated December 27, 2018

3. 

   Free

   NSD neck rings for 3d printing

   By beeweasd

   these have been split into small sections to fit on a 3d printer.
   

   321 downloads

      (0 reviews)

   4 comments

   Updated November 13, 2016

4. 

   Free

   NSD Moflash lens

   By cdngoose

   I truly believe the 3D printer is a Dalek builders best friend. Since the Moflash Lens is no longer available we can now print one. I used this file from Thingverse and it is quite acceptable. Below is the caveat for its use.
    
   A close approximation of the Moflash lenses used for Dalek NSD dome lights. I do not have a real one, so attempted this for my own NSD.
   Dimensioned to fit inside the housings described in the Project Dalek NSD plans.
   Print in a transparent or semi-transparent material as desired.
    
   Dalek NSD Moflash-style Dome Light Lens by miproductions is licensed under the Creative Commons - Attribution - Non-Commercial license.
   So what's this mean?
   Remixing or Changing this Thing is allowed.
   Commercial use is not allowed.
    
   Once again I did not create this file but I have used it and it needs to be available to PDF members.
   cdngoose
    
   Note: Above are the pictures I took during and after printing, first one is nearing the end of print and the second is print finished. The third one is with the filler removed while the last one is with a flashlight with weak batteries. all in all I prefer this look over the original Moflash unit, I like the silver finish and it glows nicely.. Once the light hits it their is an oddness about the silver glow that makes it far more Dalek worthy!
    
   Enjoy, and with the discontinued production of these lenses take heart that we will have them forever now! Gone are the days of scrounging and pleading in back corners for obscure parts to make our obsession!
    
   cdngoose
   

   319 downloads

      (1 review)

   0 comments

   Updated May 18, 2016

5. 

   Free

   2005 Plunger

   By elmoray

   I wanted to give back to the group...
   Here is a version of the 2005 plunger that I made for my Dalek. You can find more info on Thingiverse: http://www.thingiverse.com/thing:210939
   

   318 downloads

      (2 reviews)

   4 comments

   Submitted December 23, 2013

6. 

   Free

   Dalek Gatling Gun

   By RattyVulcan

   These files allow you to build a version of the Gatling Gun which includes integrated pistol grip and a housing for a motor and electronics to replicate the lights and spinning effect of a 'real' gatling gun as it slows due to friction.
    
   More details can be found here: 
    
   

   313 downloads

      (1 review)

   0 comments

   Submitted June 28, 2022

7. 

   Free

   Louis Marx Bump and Go Toy Dalek

   By erichdalek

   This is a model of the Louis Marx Bump and Go Toy Dalek of the 60's, as used in the production of Evil of the Daleks per information from this gallery entry and this BBC photo.
    
   Provided is:
   -.SLDPRT of the whole thing, for your personal improvements or modifications
   -.STL of the whole thing
   -.STL's of it with the eyestalk and appendages in separate files for you to glue on
    
   Let me know any ways I could better the screen-accuracy or proportions.
    
    
   

   307 downloads

      (0 reviews)

   1 comment

   Submitted August 7, 2021

8. 

   Free

   NSD Gunbox Detail

   By Macropod80

   I've done this in two layers to make the flat faces easier to sand (before sticking them together). I had trouble getting them to stay flat while printing, so ended up having to print them in halves to prevent lifting. I'd recommend painting them on both sides before screwing them on, to ensure they don't start curling up at the corners as time passes. I've noticed that's happened to some of the BBC Daleks.
   

   306 downloads

      (1 review)

   0 comments

   Submitted July 5, 2020

9. 

   Free

   Dalek Eyestalk Discs

   By cdngoose

   Here is a simple file, I have found a baby Blue PLA filament that is quite close in colour and these simple files can be adjusted to suit the size you need for your own Dalek. They can also be painted if you don't have access to the light blue filament..
   

   303 downloads

      (0 reviews)

   3 comments

   Updated May 29, 2016

10. 

    Free

    NSD Shoudlers STL

    By daviddz

    This is just the Shoulder section of the Solid works NSD 1.0.0 by cjorgensenmd
    I took the fiberglass NSD shoulder.SLDPRT file, and used Grab CAD to convert it to an STL file since I don't have Solidworks.
    I then used Mesh Mixer to cut it in to quarters that would fit on my CR-10 Max printer.
     
    NOTE: I have not tried printing this (Yet), though all files are water tight, and Should print OK. 
    

    302 downloads

       (1 review)

    0 comments

    Updated November 2, 2020

11. 

    Free

    2005 Slats

    By ddoherty958

    These are the 2005 full size slats. I had some difficult with the rear of the wide slat, It may need sanding to get a good fit. I may upload a second version once I get it on my NSD.
     
    Enjoy!
    

    300 downloads

       (0 reviews)

    0 comments

    Updated June 10, 2020

12. 

    Free

    NDP Neck Rings

    By threegringos

    I created these files for Orin - my NDP Dalek build.  All measurements were taken from the PDF plans.
     
    You need to print 12 of each file. I used PLA with 1mm wall thickness and 10% fill, but I would advise to go thicker - maybe 1.5mm, as the parts will warp under direct sunlight. Alternatively, try using ABS, which is less sensitive to ambient temperature.
     
    For assembly, start at the bottom with Layer 1, then build up as follows:  Layer 2 base, Layer 2, Layer 3 base, Layer 3, Layer 4 base, Layer 4.  I added some strength by offsetting each base layer so that the joints did not all align vertically.
     
    

    291 downloads

       (0 reviews)

    1 comment

    Submitted March 4, 2018

13. 

    Free

    Complete NSD Scale Model

    By audrey2

    All the parts for a scale NSD that can be printed and assembled.
    The parts are designed to go together at a 1/5 scale, and while it may work in other scales I haven't tried them yet, so that's up to you to play around with.
    You can see how I printed mine and put mine together when printed on a Replicator 2 here.
    

    287 downloads

       (2 reviews)

    8 comments

    Submitted June 12, 2014

14. 

    Free

    Imperial Dalek 5 inch Model Kit

    By audrey2

    To make up for the fact that there is no sufficiently accurate 5 inch model Imperial Dalek, here is a small 3D printable model kit to create your own. 
    This was modelled in Blender, with FDM style 3D printing in mind (although if anyone makes a resin one, please let me know, I'd love to see how it turns out), and the parts have a tolerance of around 0.15mm to fit together. 
     
     
    Only the plunger and the shoulders require printing with support material, and I have provided a visual instruction booklet showing the basics of how to assemble the model. 
    

    264 downloads

       (2 reviews)

    4 comments

    Updated April 25, 2020

15. 

    Free

    Shawcraft Eye V2

    By cdngoose

    This file is for the Shawcraft version of the Eye and is Version 2 already, I normally install the eye on a 3/4 inch ABS threaded tube so version 1 has an opening to accept that setup. However, everyone has a different way of installing the eye to the eyestalk and I had this file altered to allow the builder a choice of what size hole they need. Though this file does have a pilot hole which is centered for you already. The picture you see is the Eye I do have installed on Nyder and I will only use this file from now on when I'm making a Shawcraft Dalek! No more magic 8 ball and a can of tomato soup with 10 pounds of Bondo!
    Once again I need to Thank Philip McNulty for all his efforts in drawing up these parts for me and for all PDF members.
     Their are two inserts for this Eye which will cover most years of Shawcraft Daleks included in this download.
     
    Cdngoose.
    

    257 downloads

       (1 review)

    0 comments

    Updated April 17, 2017

16. 

    Free

    NSD Gun Front and Rear

    By simon83079

    Exactly was it says on the tin. Modelled direct from the plans. Has been printed and looks great.
      
    

    252 downloads

       (0 reviews)

    0 comments

    Submitted January 8, 2019

17. 

    Free

    Gun Boss rear

    By chrisosborne

    Changed relief at back for ball joint, otherwise solid. Holes on the model are oversized.
    

    247 downloads

       (1 review)

    2 comments

    Updated May 15, 2013

18. 

    Free

    NDP Eye

    By threegringos

    Here are the eye model files that I created for Orin - my NDP dalek build.  All measurements were taken directly from the PDF plans.
    You need to print one Front, one Rear, and eight Fins for the eye, and five Rings for the eye-stalk.  I printed everything using 1.5mm wall thickness and 15% fill. 
     
    Everything was assembled with friction fit.  No glue or screws.  The fins fit tightly into the body of the eye and hold everything together. 
     
    When assembling, I started by inserting the rear of all the fins into the rearmost point of the eye body, then folded them inward one at a time.  This works nicely because you can easily access any electronics that you install into the eye.  Just open out the fins from the front until the eye front drops out.
    

    244 downloads

       (1 review)

    2 comments

    Updated March 4, 2018

19. 

    Free

    Gun Boss front

    By chrisosborne

    Solid with oversized holes.
    

    242 downloads

       (1 review)

    1 comment

    Updated May 15, 2013

20. 

    Free

    Torch Eye kit for Planet Supreme Dalek

    By Sparky_Butane

    All the pieces are ready for printing. I have designed them with allowance so they should fit together without sanding, hopefully. Please message me with questions or comments.
    Thanks and Enjoy
    

    242 downloads

       (1 review)

    0 comments

    Updated June 12, 2016

21. 

    Free

    Imperial Dalek Eyediscs

    By Aaron J Climas

    A relatively quick version of the Imperial Dalek eye discs. They are based on (A forum members- someone please help!) measurements from a few years ago. I haven't had a chance to test print these. 
     
    Included are all four discs as separate files as well as a combined download of all four. The discs are about 11mm or so apart, and have a 25/26 mm hole partially extruded on both sides of each disc, but not 
    the whole way through so you have a little choice of construction.
     
    Please give me a shout if you have any issues with them.
     
    
    

    239 downloads

       (0 reviews)

    2 comments

    Updated February 13, 2017

22. 

    Free

    NSD Cowl Quadrants

    By Pgordon

    This is the NSD Cowl 1.0.0 By Macropod80, but split into 4 roughly equal sized quadrants which can be printed on printers with a much smaller build area. I created these splits for my Flashforge Adventurer 3 which only has 150x150x150 build area, and they print fine, and join together pretty well with nice tight seams. Someone more proficient at 3D modelling than I could perhaps improve these models by adding some alignment/reinforcing tabs along the joins to aid with accurate assembly and strengthen the joins in the assembled piece. In my case I joined the pieces with superglue and held them together by hand while the initial bond formed.
     
    Whilst the seams are fairly tight & neat, they're not invisible, so the completed assembled cowl will still need filling, sanding & painting. The parts need to be printed with supports, which are not in these model files, you'll have to add them in your slicer.
     
    I printed these in PLA with 0.2 layer height, and each quadrant is roughly a 16 hour print at the highest quality on my machine.
     
    Hope this helps someone!
    

    238 downloads

       (1 review)

    1 comment

    Submitted October 28, 2020

23. 

    Free

    Renegade_Dalek_Kit.zip

    By audrey2

    I ended up modifying quite a lot of the pieces so they now all fit together and print really well. It's a great balance between detail and ease of construction. So I have no doubt that any member of Project Dalek would be able to assemble it. It's a great deal simpler than the NSD, which was more designed for me with other people being able to assemble it simply being an afterthought.
    As such I've created an instruction manual for anyone interested in either putting the model together or simply seeing how it was designed.
     
    Renegade Dalek Instruction Booklet.pdf
    

    235 downloads

       (0 reviews)

    1 comment

    Updated June 6, 2019

24. 

    Free

    Slat-large-shell-STL

    By acrylikhan

    Large Slate for NSD type Dalek. Verison 2. Format STL. For Stereolithography.
    

    234 downloads

       (0 reviews)

    2 comments

    Updated February 7, 2013

25. 

    Free

    Full size NSD Dome solidworks for 3d printing

    By cjorgensenmd

    I modeled the NSD dome in solidworks with the intention of breaking it up into parts small enough to 3d print and later on make a fibeglass mold from. The cone near the eye cutout will help when an air valve is bolted onto the fiberglass mold. This air valve will enable easy mold release.
    

    233 downloads

       (0 reviews)

    0 comments

    Submitted April 6, 2017