-
Registration
Please register an account to access the Forum topics and features.
An Active Membership subscription gives you access to extra features and exclusive content!
Choosing Active Membership is a great way of supporting the community and showing your appreciation for our resources.
Please note that you need to register BEFORE you can use Facebook, Twitter or Google as a sign in method.
Files For 3D Printing
Files that can be used to for 3D printing physical versions, using your own printer or a service such as Shapeways etc.
Note that files for CNC and laser cutting can be found in their own sub-section, inside.
246 files
-
Free
Paradigm: Eye
By Ultrastar
Paradigm: Eye
By: Ultrastar
Intended for Dalek builders out there with the ability to 3D print models. This is a 3D model of the Paradigm Dalek eye. This model was created with the purpose of 3D-Printing. However, with this being a 1:1 scale and 100% accurate model it can also be used as a reference for your own builds. Feel free to ask questions about this model as you see fit.
99 downloads
(0 reviews)0 comments
Submitted
-
Free
2005 series hemisphere
By Snape757
2005 series hemisphere, add an extrusion to the bottom for the thickness of your material, or ask me and I will.
98 downloads
(0 reviews)0 comments
Submitted
-
Free
(0 reviews)0 comments
Submitted
-
Free
Movie Dalek Dome
By Chris Moliere
Another dome! This is the Movie Dalek dome, using the measurements given in the updated plans. This can be used for a fiberglass mould, or just used as is. As always, enjoy!
97 downloads
(1 review)0 comments
Updated
-
Free
Mark 3 Dome stl files for lazy susan bearing ring
By Adam Gready
This is my attempt at a Mark 3 dome with a shelf designed in for a lazy susan bearing ring. I have 3d printed and assembled this but i haven't actually assembled the dome using the bearing ring so I can't guarantee it is exactly what you are looking for. The files include the complete dome, the dome cut into quarters with the lower brim separated into 1/8ths. Also included is a gluing jig for aligning the brim pieces which seemed to work quite well. The dome quarters wont fit on a 200x200 bed sorry. I have struggled to slice it up finer as Tinkercad was struggling with my request. It can be cut easily enough using meshmixer and if you slice the top of the dome off you can get 1/8th size pieces smaller enough to fit on a smaller bed. Please note all files are at 1/10th scale so make sure you increase by 1000% in your slicer!
97 downloads
(1 review)0 comments
Submitted
-
Free
Imperial Dalek Eyeball
By Aaron J Climas
Hey guys.
This is a STL file of the Imperial Dalek eyeball. It's in two halves that need to be printed and glued together.
It is a pair of STL files. They are much larger than normal as I have found issues with low resolution geometry making the prints come out with hard edges. If this is too much geometry I will remodel and upload again.
The front of the eye isn't as deep as the original prop, because it makes adding the front much harder! However I could do that variation if someone was keen.
The front of the eyeball itself is slightly rounded off as per the original, rather than being dead flat.
The rear of the ball has a nice flat section for tube to sit flush against, as well as a pilot hole included for drilling a central hole.
I haven't printed this file yet, but intend to tomorrow!
EDIT. The rear of the eyeball has a hole in he model. I have fixed the model, but not uploaded yet. This will be fixed soon.
EDIT- The previous upload didn't include the front of the eye. I only just saw a message about it then. (4th March 2016.)
95 downloads
-
Free
Dead Planet Octagon
By Ferrain
Quick Sketchup generated file for the octagonal supports of a Dead Planet Dalek Gun.
Dimensions taken from PDF Plans for 3mm gun gods, gun barrel hole slightly oversized after first print, thickness 2.5mm.
16mins print time on medium quality 15% infill
No further versions planned, just done for proof of concept.
93 downloads
(0 reviews)0 comments
Updated
-
Free
DalekStorm-Parts2.zip
By Djsloanau
Attached is the zip of all STL parts to date as well as a couple of the Lightwave 2015 object files for Djsloanau's 1/6 Scale 3D Printed Dalek Storm. It has been 3 years since I started the project and I don't know if or when I'll get back to it. If you can use this to complete a Storm I'd love to see your photos.
93 downloads
-
Free
Imperial Dalek Plunger v002
By Aaron J Climas
Thanks to Shane for helping me out with dimensions on this! Dalek Candi has an Imperial plunger that has original heritage. He was kind enough to measure up his plunger for me and I have build a 3D model of it based on those dimensions.
To my eyes, the front feels too big, however I haven't seen an original in hand, or printed this one yet. So I can't judge.
The rear section I have deliberate made quite soft, as the original casts are, and I feel doing a perfect computer set of straight angles wouldn't give the right feeling to the whole thing. There are only 120 verts around the circumference, I could potentially increase that if anyone wanted to make a more detailed print than that. Most people, I imagine will be using relatively low end printers that will require cleanup anyway, so I don't think it should be a problem.
Potentially if required I could split it to a front and back, so the front dish/ surround could be printed, then the rear 'tower' printed and then joined. In my experience prints often warp somewhere and joining like that often ends up with parts that don't join well.
It was created in Autodesk Maya, and the front ring should be about 120mm to give sense of overall scale. Please give me a shout and show images if you print it, as I would love to see the results.
All the best,
Aaron
92 downloads
(1 review)0 comments
Updated
-
Free
Accurate plunger - high poly
By ansonjames
60's/70's Style plunger created using the newer plans. Can be printed with FDM or SLA.
I added a rod at the bottom to slide onto the last stage of the arm, if you don't intend to use this part then you can import into Microsoft 3D builder, go to edit and split model.
92 downloads
-
Free
NSD Eyestalk Keyed Base
By cdngoose
This file is for the NSD eyestalk base, it was created by Ray Arell in Oregon USA. I have not printed this file yet but I like the ability of the keyed insertion of the eyestalk into the Base.
Cdngoose
from Ray
This is the base of the Dalek eye stalk. I wanted an easy method to access the dome electronics, so I put the eye stalk on a keyed lock. You insert the eye stalk and rotate it to lock it into the base.
Dalek Eye Stalk Base by elmoray is licensed under the Creative Commons - Attribution - Non-Commercial license.
So what's this mean?
Remixing or Changing this Thing is allowed.
Commercial use is not allowed.
91 downloads
-
Free
comet_dalek.zip
By tobor2288
The dome on the comet kit is not very accurate. Here are replacment domes, as well as mid sections and appendages.
There are TV and Movie domes. One of the mid sections is designed for slats, the other without. There are appendages for the movie daleks only.
These files are not really designed for home FDM printers. If you have a SLA resin printer, they should work.
I got the parts printed by Shapeways and I.Materialise in various materials.
Note: The comet daleks are not 8th scale as stated on the box. They are about 92% of 8th scale.
These files also work for the Product Enterprise Infra red movie daleks, which are the same scale. There are two of them in the attached pictures.
91 downloads
(1 review)0 comments
Updated
-
Free
NSD Neck Block (FDM)
By DrJekyll
This NSD Neck Block has been modeled for use with FDM printers, if you have access to SLS type printers you will be better off using Hallam's model.
I used Slic3r 0.9.9 to generate the gcode and printed it in PLA on my home built Mendel I2, with Sanguinololu electronics, Marlin firmware, and a J-Head hot end with the settings below.
; layer_height = 0.2
; perimeters = 2
; top_solid_layers = 5
; bottom_solid_layers = 0
; fill_density = 0.12
; perimeter_speed = 35
; infill_speed = 55
; travel_speed = 130
; nozzle_diameter = 0.35
; filament_diameter = 2.82
; extrusion_multiplier = 1
; perimeters extrusion width = 0.50mm
; infill extrusion width = 0.50mm
; solid infill extrusion width = 0.50mm
; top infill extrusion width = 0.50mm
; first layer extrusion width = 0.50mm
In addition to the Slic3r settings above I also lowered the layer height near the top to reduce the step effect.
Between 14.0mm and 15.3mm layer height was 0.15mm
Between 15.3mm and 16.3mm layer height was 0.10mm
Between 16.3mm and 17.1mm layer height was 0.05mm
I also enabled Brim with a 4mm width to minimize curling/shrinkage, and manually slowed the print speed for the last few mm's to minimize heat buildup. It did not take a lot of work to sand and paint the neck block in the images but I don't think I would want to do it for 24 of them. Casting is a better option for that many.
Steve
90 downloads
-
Free
Imperial Dalek Dome lights - STL
By Aaron J Climas
After the plans change on the domes/ dishes I went away and redesigned my 3D model. And although the pictures here are of the old dishes, I have
since printed out the new sized ones. They seemed to work well, the pipe I believe was around 12 months, and the dome about 25. Much faster times
due to the much smaller objects.
OLD INFORMATION ON PREVIOUS VERSION.
I needed a set of Imperial dome lights. The EMA parts looked expensive, so I 3D modelled and printed out a set myself.
When I imported them the models came in factor of 10 too small. However in STL viewer and Maya they seemed the correct size. So may have been an issue
with the printer software.
The pipe took me 18 minutes to print, and the dome 43 minutes. So just on two hours for the full set.
I thought I would share. If you have issues, give me a shout and I will repair the files.
90 downloads
(0 reviews)0 comments
Updated
-
Free
TrainWreck's NSD Skirt Hemisphere
By TrainWreck
Couldn't get the other hemesphere files on here to open for me so I modeled my own.
I based the scale off of the NSD design booklet.
Any feedback is welcome!
88 downloads
(0 reviews)0 comments
Updated
-
Free
ParadigmGunFiles.zip
By threegringos
Finally, here are the files for my new dalek paradigm gun build.
I've included a text file in the .zip to show which order to assemble the prints, and how many you need of each.
Check out my Dalek Orin build under username @threegringos
87 downloads
-
Free
Pivot.STL
By Ferrain
Eye pivot
1" hole for eyestalk shaft
Smaller centered recess for threaded bar (drilling)
Slot for threaded bar nut.
Axle extends 1.6cm each side.
Hollow axle allows for threading power cables through the assembly into the threaded bar into the eye itself.
Not yet printed off, accompanying bracket still to be designed & printed.
84 downloads
-
Free
NSD Gun Box Detail (FDM)
By DrJekyll
This NSD Gun Box Detail has been modeled for use with FDM printers, if you have access to SLS type printers you will be better off using Hallam's model.
I used Slic3r 0.9.9 to generate the gcode and printed it in PLA on my home built Mendel Prusa i2, with Sanguinololu electronics, Marlin firmware, and a J-Head hot end with the settings below.
; layer_height = 0.20
; perimeters = 2
; top_solid_layers = 5
; bottom_solid_layers = 0
; fill_density = 0.1
; perimeter_speed = 35
; infill_speed = 55
; travel_speed = 130
; nozzle_diameter = 0.35
; filament_diameter = 2.82
; extrusion_multiplier = 1
; perimeters extrusion width = 0.50mm
; infill extrusion width = 0.50mm
; solid infill extrusion width = 0.50mm
; top infill extrusion width = 0.50mm
; first layer extrusion width = 0.50mm
I also enabled Brim with a 4mm width. I should have made the brim wider as I got a bit of curling on the corners. I recommend you use a heated bed for this part.
To counteract the curling I placed the part on a disc of hardboard just bigger than the center hole. I them placed weights (cans of beans) on the corners and gently heated the part with a hair dryer until the corners dropped. They are now curling in the opposite direction which will not be a problem once bolted in place.
83 downloads
-
Free
NSD Neck Blocks - Kresty's version
By Kresty
NSD Neck Blocks - Sketchup files are in the Thingiverse thing at http://www.thingiverse.com/thing:727027 since PDF doesn't seem to like them in the post, in case you need to modify the hole.
I think they turned out fairly nice. They have fatter backs than fronts and match the PDF as well as I could. I had trouble finding the exact dimensions for the corner rounding or the position of the bearing though, but I'm happy with it. The hollow version is intended to snap a 14mm bearing into it, however I'm not sure it'll fit (I don't have one to try). Looking at it, it seems like the edges come in a little much, but it seems to align with both the PDF and photos I found, so...
Now I just need to print another 23 of them!
83 downloads
(1 review)0 comments
Submitted
-
Free
NSD Gun box front detail
By Snape757
Nice easy flat print, select solid print, no supports and best quality, doesn't take too long either.
83 downloads
(0 reviews)0 comments
Submitted
-
Free
Oil Seal Surround for 100mm hemis
By napier1973
ok i jumped on cad and changed the surround a little so it fit the 100mm hemisphhere only changed is the walls thicker.
82 downloads
(0 reviews)0 comments
Submitted
-
Free
NSD Eye Back
By Mr McGoo
CREATOR's EDIT: My apologies, I only just realised this has 8 rods, not 12 going around the eye. I'll leave the files up for now in case anyone wishes to modify them, as I don't have the time right now. My plan is to sand off the rods printed on the eye, and make/glue the vessel tubing as a separate part so to not bin the one I currently printed. Just wanted to be fully transparent about this mistake!
I created my own CAD files for the NSD eye to print because I wasn't happy with any that I found, they all needed some unsightly supports.
I designed these to be easy print (I did mine on an Ender 3, came out great) The front section doesn't need supports, orientate it so the front section faces up and it'll print nicely. The back section needs a support in the middle to print the stem, which broke off easily for me. Tolerances are pretty tight and will need some light sanding to make it a little looser. Then you just have to drill your holes for your allen bolts and you're good to go!
79 downloads
(0 reviews)0 comments
Updated
-
Free
Classic Eyeball
By Aaron J Climas
This is the front half of a classic style eyeball from the 60's. It's a slightly odd size hemisphere, and the 12 degree angle on the lip can be hard to get even.
So I have made a 3D print file, presented in both STL and OBJ format for people to print if they aren't so keen on making on themselves.
I haven't printed this item yet, but plan to later today. Although checking over the file there should be no major issues. It should fit perfectly flush with a 4" (102mm) hemisphere. It has 360 isoparms coming out across the body, so shouldn't suffer from not having enough resolution on the body.
Edit- I printed the file today, and it came out without a hitch. Although the model was 90 degrees out! Please give me a shout if you print this.
77 downloads
-
Free
NSD 'Death-Squad' Dalek claw - "Revolution of the Daleks". Fully operational
By threegringos
This is my NSD 'Death Squad' claw as seen on the Daleks in the 2021 New Year's special "Revolution of the Daleks".
I made this originally for my own Dalek, (Dalek Axel). I've been constantly getting messages through my Instagram from people who want a claw, so I thought I'd release it here on Project Dalek for the community to use.
This 3D model was developed solely from screenshots and promotional images. It looks accurate to my eye, and some deliberate (but small) compromises were made to simplify the 3D printing process.
I used Fusion360 to create this model. The claw is split into multiple parts for ease of printing.
The ZIP file contains photos and instructions.
NOTE:
For assembly, you will need some 3mm diameter stainless steel rods or dowels for pivots. I bought a pack from Amazon, and cut them down to size.
You will need to provide your own arm (and Dalek) to mount the claw onto. The claw will fit a 25.4mm (1 inch) diameter pipe.
Enjoy!
77 downloads
(1 review)0 comments
Submitted
-
Free
70's Dalek eyes 2 - Genesis of the Daleks style eye
By ansonjames
No supports required except for the back of the eye, remove supports on this part and insert the ring which is for aligning the front and the back of the eye.
You may need to reduce the size of the joiner to 99% to help it fit into the recesses, do this in your slicer and scaling.
I recommend 20% infill and 3 perimeters. Send me a PM if you need assistance!
11MM diameter hole is for the eye stalk/pivot files which I'll upload soon, the finished prints are kept together with an M10 threaded bar and nuts.
76 downloads
(0 reviews)0 comments
Submitted
-
Top Downloads
Week
-
Free
-
Free
-
Free
-
Free
-
Free
Month
-
Free
-
Free
-
Free
-
Free
-
Free
Year
-
Free
-
Free
-
Free
-
Free
-
Free
All Time
-
Free
-
Free
-
Free
-
Free
-
Free
-
-
Recent File Reviews
-
Michael56 2
I'm in my late 60's. I live in Australia and have always enjoyed Doctor Who from the very first episode aired here around 1965 when I was 9 years old. Thought how amazing it would be to have a Dalek but had no idea how or where to even begin UNTIL I came across this site. Thanks for giving me the opportunity to at least be able to start on a Dalek build and will detail my progress as it goes along.
-
Mark Sheriff 6
Excellent , looks great and very well designed , well thought out . thank you
-
Marc Harris 54
I'm in my 50s and have since I was a boy watching Dr Who in the 70s always dreamed of making a Dalek for fun, now I have the time and resources, along with your forum's help it's time to live that dream.
I have watched some of the members videos, and I am very impressed with what I have seen.
Long live the Who verse.
I will document my progress and share any innovations I make
-
Chris R 25
Great set of models that printed and fitted together really easily. Can't comment on accuracy as I'm no expert but very happy with the result
-
Dalek Hal 312
Great file, easy to print
-
doctorone 3
Great plan but the pivot does not print as it is not complete like the eye stalk
-
-
Download Statistics
-
Recent File Comments
-
-
By WhosWho · Posted
@RepeatedMemeDid you change something? I haven't touched anything. -
By RepeatedMeme · Posted
@WhosWho @dalekray It's only showing an update because the (written) details were edited. -
-
By life size · Posted
I printed mine in PTEG, 235 nozzle, 60 Bed , no supports and it printed with no mess at all. I ran it at a 40 percent print speed, and the orientation was large cup facing down on my print. -
By John · Posted
See this FAQ topic for more on Downloads availability: -
By ChristmasDalek · Posted
Welcome to the forum! Sorry you have encountered a problem... While waiting for someone who knows more about the downloads section than I do to answer, you may find the explanation in @Johns answer to this thread: Be well, Kathy -
By tardis112 · Posted
Why am I not permitted to download this? -
By Mark Casto · Posted
This is such a useful file for the eye it is perfect for adding a fish tank led inside and looks great thank you. -
By DarthCranium · Posted
ok @Bodule. i apologize if i caused any issue. -
By Bodule · Posted
Hi @DarthCranium Can I suggest that you ask your question in the 3D Printer Discussions section of the forum please? https://www.projectdalek.com/index.php?/forum/209-3d-printer-discussions/ That section itself may be worth a read through, as is @ChristmasDalek's post above yours 👆 here as it may provide additional useful information on how to use the forum. -
By DarthCranium · Posted
What is a good size of 3D printer youd recommend if i wanted to make a dalek of my own? please let me know when able. Thanks -
By Dalek-Nik · Posted
Moflash lenses appear to be slightly difficult these days. the best bet in my opinion is 3D printing them. there are many accurate models here that can be printed on any FDM printer you can find. there is a chance that you can find the lenses online to buy, but those sites can be slightly sketchy. depending on the filament you buy and the printer you have/find, they can be produced fairly accurately. filament can come as cheap as 17 dollars, but do keep in mind that they can some -
By Chris R · Posted
Thanks for uploading these files. Printed really nicely with the odds and sods of filament I had around and very pleased with it, haven't done any tidying up or painting but it looks great as-is.
-
-
Highest Rated Submitters
No ratings this week.
No ratings this month.
-
1
-
2
-
3
-
4
-
5
-
1
-
2
-
3
-
4
-
5
-
-
Current Donation Goals
-
Finance the Forum Hosting 2024Raised 113.00 GBP
-
-
Top Templates
-
Free
-
Free
-
Free
-
Free
-
Free
-
